root/drivers/scsi/53c8xx_d.h

/* [previous][next][first][last][top][bottom][index][help] */

INCLUDED FROM


   1 unsigned long SCRIPT[] = {
   2 /*
   3 ; NCR 53c810 driver, main script
   4 ; Sponsored by 
   5 ;       iX Multiuser Multitasking Magazine
   6 ;       hm@ix.de
   7 ;
   8 ; Copyright 1993, Drew Eckhardt
   9 ;      Visionary Computing 
  10 ;      (Unix and Linux consulting and custom programming)
  11 ;      drew@Colorado.EDU
  12 ;      +1 (303) 786-7975
  13 ;
  14 ; TolerANT and SCSI SCRIPTS are registered trademarks of NCR Corporation.
  15 ;
  16 ; PRE-ALPHA
  17 ;
  18 ; For more information, please consult 
  19 ;
  20 ; NCR 53C810
  21 ; PCI-SCSI I/O Processor
  22 ; Data Manual
  23 ;
  24 ; NCR 53C710 
  25 ; SCSI I/O Processor
  26 ; Programmers Guide
  27 ;
  28 ; NCR Microelectronics
  29 ; 1635 Aeroplaza Drive
  30 ; Colorado Springs, CO 80916
  31 ; 1+ (719) 578-3400
  32 ;
  33 ; Toll free literature number
  34 ; +1 (800) 334-5454
  35 ;
  36 ; IMPORTANT : This code is self modifying due to the limitations of 
  37 ;       the NCR53c7,8xx series chips.  Persons debugging this code with
  38 ;       the remote debugger should take this into account, and NOT set
  39 ;       breakpoints in modified instructions.
  40 ;
  41 ;
  42 ; Design:
  43 ; The NCR53c7x0 family of SCSI chips are busmasters with an onboard 
  44 ; microcontroller using a simple instruction set.   
  45 ;
  46 ; So, to minimize the effects of interrupt latency, and to maximize 
  47 ; throughput, this driver offloads the practical maximum amount 
  48 ; of processing to the SCSI chip while still maintaining a common
  49 ; structure.
  50 ;
  51 ; Where tradeoffs were needed between efficiency on the older
  52 ; chips and the newer NCR53c800 series, the NCR53c800 series 
  53 ; was chosen.
  54 ;
  55 ; While the NCR53c700 and NCR53c700-66 lacked the facilities to fully
  56 ; automate SCSI transfers without host processor intervention, this 
  57 ; isn't the case with the NCR53c710 and newer chips which allow 
  58 ;
  59 ; - reads and writes to the internal registers from within the SCSI
  60 ;       scripts, allowing the SCSI SCRIPTS(tm) code to save processor
  61 ;       state so that multiple threads of execution are possible, and also
  62 ;       provide an ALU for loop control, etc.
  63 ; 
  64 ; - table indirect addressing for some instructions. This allows 
  65 ;       pointers to be located relative to the DSA ((Data Structure
  66 ;       Address) register.
  67 ;
  68 ; These features make it possible to implement a mailbox style interface,
  69 ; where the same piece of code is run to handle I/O for multiple threads
  70 ; at once minimizing our need to relocate code.  Since the NCR53c700/
  71 ; NCR53c800 series have a unique combination of features, making a 
  72 ; a standard ingoing/outgoing mailbox system, costly, I've modified it.
  73 ;
  74 ; - Commands are stored in a linked list, rather than placed in 
  75 ;       arbitrary mailboxes.  This simplifies the amount of processing
  76 ;       that must be done by the NCR53c810.
  77 ;
  78 ; - Mailboxes are a mixture of code and data.  This lets us greatly
  79 ;       simplify the NCR53c810 code and do things that would otherwise
  80 ;       not be possible.
  81 
  82 ;
  83 ; Note : the DSA structures must be aligned on 32 bit boundaries,
  84 ; since the source and destination of MOVE MEMORY instructions 
  85 ; must share the same alignment and this is the alignment of the
  86 ; NCR registers.
  87 ;
  88 
  89 ABSOLUTE dsa_temp_jump_resume = 0       ; Patch to dsa_jump_resume
  90                                         ;       in current dsa
  91 ABSOLUTE dsa_temp_lun = 0               ; Patch to lun for current dsa
  92 ABSOLUTE dsa_temp_dsa_next = 0          ; Patch to dsa next for current dsa
  93 ABSOLUTE dsa_temp_sync = 0              ; Patch to address of per-target
  94                                         ;       sync routine
  95 ABSOLUTE dsa_temp_target = 0            ; Patch to id for current dsa
  96 
  97 
  98 
  99 ENTRY dsa_code_template
 100 dsa_code_template:
 101 
 102 ; Define DSA structure used for mailboxes
 103 
 104 ; wrong_dsa loads the DSA register with the value of the dsa_next
 105 ; field.
 106 ;
 107 wrong_dsa:
 108 ;               Patch the MOVE MEMORY INSTRUCTION such that 
 109 ;               the destination address is that of the OLD next
 110 ;               pointer.
 111         MOVE MEMORY 4, dsa_temp_dsa_next, reselected_ok + 8
 112 
 113 at 0x00000000 : */      0xc0000004,0x00000000,0x00000660,
 114 /*
 115 
 116         MOVE dmode_memory_to_ncr TO DMODE       
 117 
 118 at 0x00000003 : */      0x78380000,0x00000000,
 119 /*
 120         MOVE MEMORY 4, dsa_temp_dsa_next, addr_scratch
 121 
 122 at 0x00000005 : */      0xc0000004,0x00000000,0x00000000,
 123 /*
 124         MOVE dmode_memory_to_memory TO DMODE
 125 
 126 at 0x00000008 : */      0x78380000,0x00000000,
 127 /*
 128         CALL scratch_to_dsa
 129 
 130 at 0x0000000a : */      0x88080000,0x00000800,
 131 /*
 132         JUMP reselected_check_next
 133 
 134 at 0x0000000c : */      0x80080000,0x000005ac,
 135 /*
 136 
 137 ABSOLUTE dsa_check_reselect = 0
 138 ; dsa_check_reselect determines weather or not the current target and
 139 ; lun match the current DSA
 140 ENTRY dsa_code_check_reselect
 141 dsa_code_check_reselect:
 142         MOVE SSID TO SFBR               ; SSID contains 3 bit target ID
 143 
 144 at 0x0000000e : */      0x720a0000,0x00000000,
 145 /*
 146         JUMP REL (wrong_dsa), IF NOT dsa_temp_target, AND MASK 7
 147 
 148 at 0x00000010 : */      0x80840700,0x00ffffb8,
 149 /*
 150         MOVE dmode_memory_to_ncr TO DMODE
 151 
 152 at 0x00000012 : */      0x78380000,0x00000000,
 153 /*
 154         MOVE MEMORY 1, reselected_identify, addr_sfbr
 155 
 156 at 0x00000014 : */      0xc0000001,0x00000000,0x00000000,
 157 /*
 158         JUMP REL (wrong_dsa), IF NOT dsa_temp_lun, AND MASK 7
 159 
 160 at 0x00000017 : */      0x80840700,0x00ffff9c,
 161 /*
 162         MOVE dmode_memory_to_memory TO DMODE
 163 
 164 at 0x00000019 : */      0x78380000,0x00000000,
 165 /*
 166 ;               Patch the MOVE MEMORY INSTRUCTION such that
 167 ;               the source address is that of this dsas
 168 ;               next pointer.
 169         MOVE MEMORY 4, dsa_temp_dsa_next, reselected_ok + 4
 170 
 171 at 0x0000001b : */      0xc0000004,0x00000000,0x0000065c,
 172 /*
 173         CALL reselected_ok
 174 
 175 at 0x0000001e : */      0x88080000,0x00000658,
 176 /*
 177         CALL dsa_temp_sync      
 178 
 179 at 0x00000020 : */      0x88080000,0x00000000,
 180 /*
 181 ENTRY dsa_jump_resume
 182 dsa_jump_resume:
 183         JUMP 0                          ; Jump to resume address
 184 
 185 at 0x00000022 : */      0x80080000,0x00000000,
 186 /*
 187 ENTRY dsa_zero
 188 dsa_zero:
 189         MOVE dmode_ncr_to_memory TO DMODE                       ; 8
 190 
 191 at 0x00000024 : */      0x78380000,0x00000000,
 192 /*
 193         MOVE MEMORY 4, addr_temp, dsa_temp_jump_resume          ; 16    
 194 
 195 at 0x00000026 : */      0xc0000004,0x00000000,0x00000000,
 196 /*
 197         MOVE dmode_memory_to_memory TO DMODE                    ; 28
 198 
 199 at 0x00000029 : */      0x78380000,0x00000000,
 200 /*
 201         JUMP dsa_schedule                                       ; 36
 202 
 203 at 0x0000002b : */      0x80080000,0x000000b4,
 204 /*
 205 ENTRY dsa_code_template_end
 206 dsa_code_template_end:
 207 
 208 ; Perform sanity check for dsa_fields_start == dsa_code_template_end - 
 209 ; dsa_zero, puke.
 210 
 211 ABSOLUTE dsa_fields_start =  36 ; Sanity marker
 212                                 ;       pad 12
 213 ABSOLUTE dsa_next = 48          ; len 4 Next DSA
 214                                 ; del 4 Previous DSA address
 215 ABSOLUTE dsa_cmnd = 56          ; len 4 Scsi_Cmnd * for this thread.
 216 ABSOLUTE dsa_select = 60        ; len 4 Device ID, Period, Offset for 
 217                                 ;       table indirect select
 218 ABSOLUTE dsa_msgout = 64        ; len 8 table indirect move parameter for 
 219                                 ;       select message
 220 ABSOLUTE dsa_cmdout = 72        ; len 8 table indirect move parameter for 
 221                                 ;       command
 222 ABSOLUTE dsa_dataout = 80       ; len 4 code pointer for dataout
 223 ABSOLUTE dsa_datain = 84        ; len 4 code pointer for datain
 224 ABSOLUTE dsa_msgin = 88         ; len 8 table indirect move for msgin
 225 ABSOLUTE dsa_status = 96        ; len 8 table indirect move for status byte
 226 ABSOLUTE dsa_msgout_other = 104 ; len 8 table indirect for normal message out
 227                                 ; (Synchronous transfer negotiation, etc).
 228 ABSOLUTE dsa_end = 112
 229 
 230 ; Linked lists of DSA structures
 231 ABSOLUTE issue_dsa_head = 0     ; Linked list of DSAs to issue
 232 ABSOLUTE reconnect_dsa_head = 0 ; Link list of DSAs which can reconnect
 233 
 234 ; These select the source and destination of a MOVE MEMORY instruction
 235 ABSOLUTE dmode_memory_to_memory = 0x0
 236 ABSOLUTE dmode_memory_to_ncr = 0x0
 237 ABSOLUTE dmode_ncr_to_memory = 0x0
 238 ABSOLUTE dmode_ncr_to_ncr = 0x0
 239 
 240 ABSOLUTE addr_scratch = 0x0
 241 ABSOLUTE addr_sfbr = 0x0
 242 ABSOLUTE addr_temp = 0x0
 243 
 244 
 245 ; Interrupts - 
 246 ; MSB indicates type
 247 ; 0     handle error condition
 248 ; 1     handle message 
 249 ; 2     handle normal condition
 250 ; 3     debugging interrupt
 251 ; 4     testing interrupt 
 252 ; Next byte indicates specific error
 253 
 254 ; XXX not yet implemented, I'm not sure if I want to - 
 255 ; Next byte indicates the routine the error occurred in
 256 ; The LSB indicates the specific place the error occurred
 257  
 258 ABSOLUTE int_err_unexpected_phase = 0x00000000  ; Unexpected phase encountered
 259 ABSOLUTE int_err_selected = 0x00010000          ; SELECTED (nee RESELECTED)
 260 ABSOLUTE int_err_unexpected_reselect = 0x00020000 
 261 ABSOLUTE int_err_check_condition = 0x00030000   
 262 ABSOLUTE int_err_no_phase = 0x00040000
 263 ABSOLUTE int_msg_wdtr = 0x01000000              ; WDTR message received
 264 ABSOLUTE int_msg_sdtr = 0x01010000              ; SDTR received
 265 ABSOLUTE int_msg_1 = 0x01020000                 ; single byte special message
 266                                                 ; received
 267 
 268 ABSOLUTE int_norm_select_complete = 0x02000000  ; Select complete, reprogram
 269                                                 ; registers.
 270 ABSOLUTE int_norm_reselect_complete = 0x02010000        ; Nexus established
 271 ABSOLUTE int_norm_command_complete = 0x02020000 ; Command complete
 272 ABSOLUTE int_norm_disconnected = 0x02030000     ; Disconnected 
 273 ABSOLUTE int_norm_aborted =0x02040000           ; Aborted *dsa
 274 ABSOLUTE int_norm_reset = 0x02050000            ; Generated BUS reset.
 275 ABSOLUTE int_debug_break = 0x03000000           ; Break point
 276 ABSOLUTE int_debug_scheduled = 0x03010000       ; new I/O scheduled 
 277 ABSOLUTE int_debug_idle = 0x03020000            ; scheduler is idle
 278 ABSOLUTE int_debug_dsa_loaded = 0x03030000      ; dsa reloaded
 279 ABSOLUTE int_debug_reselected = 0x03040000      ; NCR reselected
 280 ABSOLUTE int_debug_head = 0x03050000            ; issue head overwritten
 281 
 282 ABSOLUTE int_test_1 = 0x04000000                ; Test 1 complete
 283 ABSOLUTE int_test_2 = 0x04010000                ; Test 2 complete
 284 ABSOLUTE int_test_3 = 0x04020000                ; Test 3 complete
 285                                                 
 286 EXTERNAL NCR53c7xx_msg_abort            ; Pointer to abort message
 287 EXTERNAL NCR53c7xx_msg_reject           ; Pointer to reject message
 288 EXTERNAL NCR53c7xx_zero                 ; long with zero in it, use for source
 289 EXTERNAL NCR53c7xx_sink                 ; long to dump worthless data in
 290 
 291 ; Pointer to final bytes of multi-byte messages
 292 ABSOLUTE msg_buf = 0
 293 
 294 ; Pointer to holding area for reselection information
 295 ABSOLUTE reselected_identify = 0
 296 ABSOLUTE reselected_tag = 0
 297 
 298 ; Request sense command pointer, it's a 6 byte command, should
 299 ; be constant for all commands since we always want 16 bytes of 
 300 ; sense and we don't need to change any fields as we did under 
 301 ; SCSI-I when we actually cared about the LUN field.
 302 ;EXTERNAL NCR53c7xx_sense               ; Request sense command
 303 
 304 
 305 ; dsa_schedule  
 306 ; PURPOSE : after a DISCONNECT message has been received, and pointers
 307 ;       saved, insert the current DSA structure at the head of the 
 308 ;       disconnected queue and fall through to the scheduler.
 309 ;
 310 ; CALLS : OK
 311 ;
 312 ; INPUTS : dsa - current DSA structure, reconnect_dsa_head - list
 313 ;       of disconnected commands
 314 ;
 315 ; MODIFIES : SCRATCH, reconnect_dsa_head
 316 ; 
 317 ; EXITS : always passes control to schedule
 318 
 319 ENTRY dsa_schedule
 320 dsa_schedule:
 321 
 322 ;
 323 ; Calculate the address of the next pointer within the DSA 
 324 ; structure of the command that is currently disconnecting
 325 ;
 326     CALL dsa_to_scratch
 327 
 328 at 0x0000002d : */      0x88080000,0x000007b8,
 329 /*
 330 ; XXX - we need to deal with the NCR53c710, which lacks an add with
 331 ;       carry instruction, by moving around the DSA alignment to avoid
 332 ;       carry in situations like this.
 333     MOVE SCRATCH0 + dsa_next TO SCRATCH0
 334 
 335 at 0x0000002f : */      0x7e343000,0x00000000,
 336 /*
 337     MOVE SCRATCH1 + 0 TO SCRATCH1 WITH CARRY
 338 
 339 at 0x00000031 : */      0x7f350000,0x00000000,
 340 /*
 341     MOVE SCRATCH2 + 0 TO SCRATCH2 WITH CARRY
 342 
 343 at 0x00000033 : */      0x7f360000,0x00000000,
 344 /*
 345     MOVE SCRATCH3 + 0 TO SCRATCH3 WITH CARRY
 346 
 347 at 0x00000035 : */      0x7f370000,0x00000000,
 348 /*
 349 
 350 ; Point the next field of this DSA structure at the current disconnected 
 351 ; list
 352     MOVE dmode_ncr_to_memory TO DMODE
 353 
 354 at 0x00000037 : */      0x78380000,0x00000000,
 355 /*
 356     MOVE MEMORY 4, addr_scratch, dsa_schedule_insert + 8
 357 
 358 at 0x00000039 : */      0xc0000004,0x00000000,0x00000100,
 359 /*
 360     MOVE dmode_memory_to_memory TO DMODE
 361 
 362 at 0x0000003c : */      0x78380000,0x00000000,
 363 /*
 364 dsa_schedule_insert:
 365     MOVE MEMORY 4, reconnect_dsa_head, 0 
 366 
 367 at 0x0000003e : */      0xc0000004,0x00000000,0x00000000,
 368 /*
 369 
 370 ; And update the head pointer.
 371     CALL dsa_to_scratch
 372 
 373 at 0x00000041 : */      0x88080000,0x000007b8,
 374 /*
 375     MOVE dmode_ncr_to_memory TO DMODE   
 376 
 377 at 0x00000043 : */      0x78380000,0x00000000,
 378 /*
 379     MOVE MEMORY 4, addr_scratch, reconnect_dsa_head
 380 
 381 at 0x00000045 : */      0xc0000004,0x00000000,0x00000000,
 382 /*
 383     MOVE dmode_memory_to_memory TO DMODE
 384 
 385 at 0x00000048 : */      0x78380000,0x00000000,
 386 /*
 387     WAIT DISCONNECT
 388 
 389 at 0x0000004a : */      0x48000000,0x00000000,
 390 /*
 391 
 392 ; schedule
 393 ; PURPOSE : schedule a new I/O once the bus is free by putting the 
 394 ;       address of the next DSA structure in the DSA register.
 395 ;
 396 ; INPUTS : issue_dsa_head - list of new commands
 397 ;
 398 ; CALLS : OK
 399 ;
 400 ; MODIFIES : SCRATCH, DSA 
 401 ;
 402 ; EXITS : if the issue_dsa_head pointer is non-NULL, control
 403 ;       is passed to select.  Otherwise, control is passed to 
 404 ;       wait_reselect.
 405 
 406 
 407 ENTRY schedule
 408 schedule:
 409     ; Point DSA at the current head of the issue queue.
 410     MOVE dmode_memory_to_ncr TO DMODE
 411 
 412 at 0x0000004c : */      0x78380000,0x00000000,
 413 /*
 414     MOVE MEMORY 4, issue_dsa_head, addr_scratch
 415 
 416 at 0x0000004e : */      0xc0000004,0x00000000,0x00000000,
 417 /*
 418     MOVE dmode_memory_to_memory TO DMODE
 419 
 420 at 0x00000051 : */      0x78380000,0x00000000,
 421 /*
 422 
 423     CALL scratch_to_dsa
 424 
 425 at 0x00000053 : */      0x88080000,0x00000800,
 426 /*
 427 
 428 
 429 
 430 
 431     ; Check for a null pointer.
 432     MOVE DSA0 TO SFBR
 433 
 434 at 0x00000055 : */      0x72100000,0x00000000,
 435 /*
 436     JUMP select, IF NOT 0
 437 
 438 at 0x00000057 : */      0x80040000,0x00000194,
 439 /*
 440     MOVE DSA1 TO SFBR
 441 
 442 at 0x00000059 : */      0x72110000,0x00000000,
 443 /*
 444     JUMP select, IF NOT 0
 445 
 446 at 0x0000005b : */      0x80040000,0x00000194,
 447 /*
 448     MOVE DSA2 TO SFBR
 449 
 450 at 0x0000005d : */      0x72120000,0x00000000,
 451 /*
 452     JUMP select, IF NOT 0
 453 
 454 at 0x0000005f : */      0x80040000,0x00000194,
 455 /*
 456     MOVE DSA3 TO SFBR
 457 
 458 at 0x00000061 : */      0x72130000,0x00000000,
 459 /*
 460     JUMP wait_reselect, IF 0
 461 
 462 at 0x00000063 : */      0x800c0000,0x00000560,
 463 /*
 464 
 465     
 466 
 467 
 468 
 469 ;
 470 ; select
 471 ;
 472 ; PURPOSE : establish a nexus for the SCSI command referenced by DSA.
 473 ;       On success, the current DSA structure is removed from the issue 
 474 ;       queue.  Usually, this is entered as a fall-through from schedule,
 475 ;       although the contingent allegiance handling code will write
 476 ;       the select entry address to the DSP to restart a command as a 
 477 ;       REQUEST SENSE.  A message is sent (usually IDENTIFY, although
 478 ;       additional SDTR or WDTR messages may be sent).  COMMAND OUT
 479 ;       is handled.
 480 ;
 481 ; INPUTS : DSA - SCSI command, issue_dsa_head
 482 ;
 483 ; CALLS : OK
 484 ;
 485 ; MODIFIES : SCRATCH, issue_dsa_head
 486 ;
 487 ; EXITS : on reselection or selection, go to select_failed
 488 ;       otherwise, fall through to data_transfer.  If a MSG_IN
 489 ;       phase occurs before 
 490 ;
 491 
 492 ENTRY select
 493 select:
 494 
 495 
 496 
 497 
 498     CLEAR TARGET
 499 
 500 at 0x00000065 : */      0x60000200,0x00000000,
 501 /*
 502 
 503 ; XXX
 504 ;
 505 ; In effect, SELECTION operations are backgrounded, with execution
 506 ; continuing until code which waits for REQ or a fatal interrupt is 
 507 ; encountered.
 508 ;
 509 ; So, for more performance, we could overlap the code which removes 
 510 ; the command from the NCRs issue queue with the selection, but 
 511 ; at this point I don't want to deal with the error recovery.
 512 ;
 513 
 514 
 515     SELECT ATN FROM dsa_select, select_failed
 516 
 517 at 0x00000067 : */      0x4300003c,0x00000694,
 518 /*
 519     JUMP select_msgout, WHEN MSG_OUT
 520 
 521 at 0x00000069 : */      0x860b0000,0x000001ac,
 522 /*
 523 ENTRY select_msgout
 524 select_msgout:
 525     MOVE FROM dsa_msgout, WHEN MSG_OUT
 526 
 527 at 0x0000006b : */      0x1e000000,0x00000040,
 528 /*
 529 
 530 
 531 
 532 
 533 
 534 
 535 
 536 
 537 
 538     ; Calculate address of dsa_next field
 539 
 540     CALL dsa_to_scratch
 541 
 542 at 0x0000006d : */      0x88080000,0x000007b8,
 543 /*
 544 
 545     MOVE SCRATCH0 + dsa_next TO SCRATCH0
 546 
 547 at 0x0000006f : */      0x7e343000,0x00000000,
 548 /*
 549     MOVE SCRATCH1 + 0 TO SCRATCH1 WITH CARRY
 550 
 551 at 0x00000071 : */      0x7f350000,0x00000000,
 552 /*
 553     MOVE SCRATCH2 + 0 TO SCRATCH2 WITH CARRY
 554 
 555 at 0x00000073 : */      0x7f360000,0x00000000,
 556 /*
 557     MOVE SCRATCH3 + 0 TO SCRATCH3 WITH CARRY
 558 
 559 at 0x00000075 : */      0x7f370000,0x00000000,
 560 /*
 561 
 562     ; Patch memory to memory move
 563     move dmode_ncr_to_memory TO DMODE
 564 
 565 at 0x00000077 : */      0x78380000,0x00000000,
 566 /*
 567     MOVE MEMORY 4, addr_scratch, issue_remove + 4
 568 
 569 at 0x00000079 : */      0xc0000004,0x00000000,0x000001fc,
 570 /*
 571 
 572 
 573     ; And rewrite the issue_dsa_head pointer.
 574     MOVE dmode_memory_to_memory TO DMODE
 575 
 576 at 0x0000007c : */      0x78380000,0x00000000,
 577 /*
 578 issue_remove:
 579 ;       The actual UPDATE of the issue_dsa_head variable is 
 580 ;       atomic, with all of the setup code being irrelevant to
 581 ;       weather the updated value being the old or new contents of 
 582 ;       dsa_next field.
 583 ;
 584 ;       To insure synchronization, the host system merely needs to 
 585 ;       do a XCHG instruction with interrupts disabled on the 
 586 ;       issue_dsa_head memory address.
 587 ;
 588 ;       The net effect will be that the XCHG instruction will return
 589 ;       either a non-NULL value, indicating that the NCR chip will not
 590 ;       go into the idle loop when this command DISCONNECTS, or a NULL
 591 ;       value indicating that the NCR wrote first and that the Linux
 592 ;       code must rewrite the issue_dsa_head pointer and set SIG_P.
 593 ;       
 594 
 595 
 596     MOVE MEMORY 4, 0, issue_dsa_head
 597 
 598 at 0x0000007e : */      0xc0000004,0x00000000,0x00000000,
 599 /*
 600 
 601 
 602 
 603 
 604 
 605 ; After a successful selection, we should get either a CMD phase or 
 606 ; some transfer request negotiation message.
 607 
 608     JUMP cmdout, WHEN CMD
 609 
 610 at 0x00000081 : */      0x820b0000,0x00000224,
 611 /*
 612     INT int_err_unexpected_phase, WHEN NOT MSG_IN 
 613 
 614 at 0x00000083 : */      0x9f030000,0x00000000,
 615 /*
 616 
 617 select_msg_in:
 618     CALL msg_in, WHEN MSG_IN
 619 
 620 at 0x00000085 : */      0x8f0b0000,0x00000354,
 621 /*
 622     JUMP select_msg_in, WHEN MSG_IN
 623 
 624 at 0x00000087 : */      0x870b0000,0x00000214,
 625 /*
 626 
 627 cmdout:
 628     INT int_err_unexpected_phase, WHEN NOT CMD
 629 
 630 at 0x00000089 : */      0x9a030000,0x00000000,
 631 /*
 632 
 633 
 634 
 635 ENTRY cmdout_cmdout
 636 cmdout_cmdout:
 637 
 638     MOVE FROM dsa_cmdout, WHEN CMD
 639 
 640 at 0x0000008b : */      0x1a000000,0x00000048,
 641 /*
 642 
 643 
 644 
 645 
 646 ;
 647 ; data_transfer  
 648 ; other_transfer
 649 ;
 650 ; PURPOSE : handle the main data transfer for a SCSI command in 
 651 ;       two parts.  In the first part, data_transfer, DATA_IN
 652 ;       and DATA_OUT phases are allowed, with the user provided
 653 ;       code (usually dynamically generated based on the scatter/gather
 654 ;       list associated with a SCSI command) called to handle these 
 655 ;       phases.
 656 ;
 657 ;       On completion, the user code passes control to other_transfer
 658 ;       which causes DATA_IN and DATA_OUT to result in unexpected_phase
 659 ;       interrupts so that data overruns may be trapped.
 660 ;
 661 ; INPUTS : DSA - SCSI command
 662 ;
 663 ; CALLS : OK
 664 ;
 665 ; MODIFIES : SCRATCH
 666 ;
 667 ; EXITS : if STATUS IN is detected, signifying command completion,
 668 ;       the NCR jumps to command_complete.  If MSG IN occurs, a 
 669 ;       CALL is made to msg_in.  Otherwise, other_transfer runs in 
 670 ;       an infinite loop.
 671 ;       
 672 
 673 data_transfer:
 674     INT int_err_unexpected_phase, WHEN CMD
 675 
 676 at 0x0000008d : */      0x9a0b0000,0x00000000,
 677 /*
 678     CALL msg_in, WHEN MSG_IN
 679 
 680 at 0x0000008f : */      0x8f0b0000,0x00000354,
 681 /*
 682     INT int_err_unexpected_phase, WHEN MSG_OUT
 683 
 684 at 0x00000091 : */      0x9e0b0000,0x00000000,
 685 /*
 686     JUMP do_dataout, WHEN DATA_OUT
 687 
 688 at 0x00000093 : */      0x800b0000,0x0000026c,
 689 /*
 690     JUMP do_datain, WHEN DATA_IN
 691 
 692 at 0x00000095 : */      0x810b0000,0x000002c4,
 693 /*
 694     JUMP command_complete, WHEN STATUS
 695 
 696 at 0x00000097 : */      0x830b0000,0x00000508,
 697 /*
 698     JUMP data_transfer
 699 
 700 at 0x00000099 : */      0x80080000,0x00000234,
 701 /*
 702 
 703 ;
 704 ; On NCR53c700 and NCR53c700-66 chips, do_dataout/do_datain are fixed up 
 705 ; whenever the nexus changes so it can point to the correct routine for 
 706 ; that command.
 707 ;
 708 
 709 
 710 ; Nasty jump to dsa->dataout
 711 do_dataout:
 712     CALL dsa_to_scratch
 713 
 714 at 0x0000009b : */      0x88080000,0x000007b8,
 715 /*
 716     MOVE SCRATCH0 + dsa_dataout TO SCRATCH0     
 717 
 718 at 0x0000009d : */      0x7e345000,0x00000000,
 719 /*
 720     MOVE SCRATCH1 + 0 TO SCRATCH1 WITH CARRY 
 721 
 722 at 0x0000009f : */      0x7f350000,0x00000000,
 723 /*
 724     MOVE SCRATCH2 + 0 TO SCRATCH2 WITH CARRY 
 725 
 726 at 0x000000a1 : */      0x7f360000,0x00000000,
 727 /*
 728     MOVE SCRATCH3 + 0 TO SCRATCH3 WITH CARRY 
 729 
 730 at 0x000000a3 : */      0x7f370000,0x00000000,
 731 /*
 732     MOVE dmode_ncr_to_memory TO DMODE
 733 
 734 at 0x000000a5 : */      0x78380000,0x00000000,
 735 /*
 736     MOVE MEMORY 4, addr_scratch, dataout_to_jump + 4
 737 
 738 at 0x000000a7 : */      0xc0000004,0x00000000,0x000002b4,
 739 /*
 740     MOVE dmode_memory_to_memory TO DMODE
 741 
 742 at 0x000000aa : */      0x78380000,0x00000000,
 743 /*
 744 dataout_to_jump:
 745     MOVE MEMORY 4, 0, dataout_jump + 4 
 746 
 747 at 0x000000ac : */      0xc0000004,0x00000000,0x000002c0,
 748 /*
 749 dataout_jump:
 750     JUMP 0
 751 
 752 at 0x000000af : */      0x80080000,0x00000000,
 753 /*
 754 
 755 ; Nasty jump to dsa->dsain
 756 do_datain:
 757     CALL dsa_to_scratch
 758 
 759 at 0x000000b1 : */      0x88080000,0x000007b8,
 760 /*
 761     MOVE SCRATCH0 + dsa_datain TO SCRATCH0      
 762 
 763 at 0x000000b3 : */      0x7e345400,0x00000000,
 764 /*
 765     MOVE SCRATCH1 + 0 TO SCRATCH1 WITH CARRY 
 766 
 767 at 0x000000b5 : */      0x7f350000,0x00000000,
 768 /*
 769     MOVE SCRATCH2 + 0 TO SCRATCH2 WITH CARRY 
 770 
 771 at 0x000000b7 : */      0x7f360000,0x00000000,
 772 /*
 773     MOVE SCRATCH3 + 0 TO SCRATCH3 WITH CARRY 
 774 
 775 at 0x000000b9 : */      0x7f370000,0x00000000,
 776 /*
 777     MOVE dmode_ncr_to_memory TO DMODE
 778 
 779 at 0x000000bb : */      0x78380000,0x00000000,
 780 /*
 781     MOVE MEMORY 4, addr_scratch, datain_to_jump + 4
 782 
 783 at 0x000000bd : */      0xc0000004,0x00000000,0x0000030c,
 784 /*
 785     MOVE dmode_memory_to_memory TO DMODE                
 786 
 787 at 0x000000c0 : */      0x78380000,0x00000000,
 788 /*
 789 datain_to_jump:
 790     MOVE MEMORY 4, 0, datain_jump + 4
 791 
 792 at 0x000000c2 : */      0xc0000004,0x00000000,0x00000318,
 793 /*
 794 datain_jump:
 795     JUMP 0
 796 
 797 at 0x000000c5 : */      0x80080000,0x00000000,
 798 /*
 799 
 800 
 801 ;
 802 ; other_transfer is exported because it is referenced by dynamically 
 803 ; generated code.
 804 ;
 805 ENTRY other_transfer
 806 other_transfer:
 807 
 808 
 809 
 810     INT int_err_unexpected_phase, WHEN CMD
 811 
 812 at 0x000000c7 : */      0x9a0b0000,0x00000000,
 813 /*
 814     CALL msg_in, WHEN MSG_IN 
 815 
 816 at 0x000000c9 : */      0x8f0b0000,0x00000354,
 817 /*
 818     INT int_err_unexpected_phase, WHEN MSG_OUT
 819 
 820 at 0x000000cb : */      0x9e0b0000,0x00000000,
 821 /*
 822     INT int_err_unexpected_phase, WHEN DATA_OUT
 823 
 824 at 0x000000cd : */      0x980b0000,0x00000000,
 825 /*
 826     INT int_err_unexpected_phase, WHEN DATA_IN
 827 
 828 at 0x000000cf : */      0x990b0000,0x00000000,
 829 /*
 830     JUMP command_complete, WHEN STATUS
 831 
 832 at 0x000000d1 : */      0x830b0000,0x00000508,
 833 /*
 834     JUMP other_transfer
 835 
 836 at 0x000000d3 : */      0x80080000,0x0000031c,
 837 /*
 838 
 839 ;
 840 ; msg_in
 841 ; munge_msg
 842 ;
 843 ; PURPOSE : process messages from a target.  msg_in is called when the 
 844 ;       caller hasn't read the first byte of the message.  munge_message
 845 ;       is called when the caller has read the first byte of the message,
 846 ;       and left it in SFBR.
 847 ;
 848 ;       Various int_* interrupts are generated when the host system
 849 ;       needs to intervene, as is the case with SDTR, WDTR, and
 850 ;       INITIATE RECOVERY messages.
 851 ;
 852 ;       When the host system handles one of these interrupts,
 853 ;       it can respond by reentering at reject_message, 
 854 ;       which rejects the message and returns control to
 855 ;       the caller of msg_in or munge_msg, accept_message
 856 ;       which clears ACK and returns control, or reply_message
 857 ;       which sends the message pointed to by the DSA 
 858 ;       msgout_other table indirect field.
 859 ;
 860 ;       DISCONNECT messages are handled by moving the command
 861 ;       to the reconnect_dsa_queue.
 862 ;
 863 ;       SAVE DATA POINTER and RESTORE DATA POINTERS are currently 
 864 ;       treated as NOPS. 
 865 ;
 866 ; INPUTS : DSA - SCSI COMMAND, SFBR - first byte of message (munge_msg
 867 ;       only)
 868 ;
 869 ; CALLS : NO.  The TEMP register isn't backed up to allow nested calls.
 870 ;
 871 ; MODIFIES : SCRATCH, DSA on DISCONNECT
 872 ;
 873 ; EXITS : On receipt of SAVE DATA POINTER, RESTORE POINTERS,
 874 ;       and normal return from message handlers running under
 875 ;       Linux, control is returned to the caller.  Receipt
 876 ;       of DISCONNECT messages pass control to dsa_schedule.
 877 ;
 878 ENTRY msg_in
 879 msg_in:
 880     MOVE 1, msg_buf, WHEN MSG_IN
 881 
 882 at 0x000000d5 : */      0x0f000001,0x00000000,
 883 /*
 884 
 885 munge_msg:
 886     JUMP munge_extended, IF 0x01                ; EXTENDED MESSAGE
 887 
 888 at 0x000000d7 : */      0x800c0001,0x00000428,
 889 /*
 890     JUMP munge_2, IF 0x20, AND MASK 0xdf        ; two byte message
 891 
 892 at 0x000000d9 : */      0x800cdf20,0x0000039c,
 893 /*
 894 ;
 895 ; I've seen a handful of broken SCSI devices which fail to issue
 896 ; a SAVE POINTERS message before disconnecting in the middle of 
 897 ; a transfer, assuming that the DATA POINTER will be implicitly 
 898 ; restored.  So, we treat the SAVE DATA POINTER message as a NOP.
 899 ;
 900 ; I've also seen SCSI devices which don't issue a RESTORE DATA
 901 ; POINTER message and assume that thats implicit.
 902 ;
 903     JUMP accept_message, IF 0x02                ; SAVE DATA POINTER
 904 
 905 at 0x000000db : */      0x800c0002,0x000004d8,
 906 /*
 907     JUMP accept_message, IF 0x03                ; RESTORE POINTERS 
 908 
 909 at 0x000000dd : */      0x800c0003,0x000004d8,
 910 /*
 911     JUMP munge_disconnect, IF 0x04              ; DISCONNECT
 912 
 913 at 0x000000df : */      0x800c0004,0x000003b4,
 914 /*
 915     INT int_msg_1, IF 0x07                      ; MESSAGE REJECT
 916 
 917 at 0x000000e1 : */      0x980c0007,0x01020000,
 918 /*
 919     INT int_msg_1, IF 0x0f                      ; INITIATE RECOVERY
 920 
 921 at 0x000000e3 : */      0x980c000f,0x01020000,
 922 /*
 923     JUMP reject_message
 924 
 925 at 0x000000e5 : */      0x80080000,0x000004b8,
 926 /*
 927 
 928 munge_2:
 929     JUMP reject_message
 930 
 931 at 0x000000e7 : */      0x80080000,0x000004b8,
 932 /*
 933 
 934 munge_save_data_pointer:
 935     CLEAR ACK
 936 
 937 at 0x000000e9 : */      0x60000040,0x00000000,
 938 /*
 939     RETURN
 940 
 941 at 0x000000eb : */      0x90080000,0x00000000,
 942 /*
 943 
 944 munge_disconnect:
 945     MOVE SCNTL2 & 0x7f TO SCNTL2
 946 
 947 at 0x000000ed : */      0x7c027f00,0x00000000,
 948 /*
 949     CLEAR ACK
 950 
 951 at 0x000000ef : */      0x60000040,0x00000000,
 952 /*
 953 
 954 
 955 ; Pass control to the DSA routine.  Note that we can not call
 956 ; dsa_to_scratch here because that would clobber temp, which 
 957 ; we must preserve.
 958     MOVE DSA0 TO SFBR
 959 
 960 at 0x000000f1 : */      0x72100000,0x00000000,
 961 /*
 962     MOVE SFBR TO SCRATCH0
 963 
 964 at 0x000000f3 : */      0x6a340000,0x00000000,
 965 /*
 966     MOVE DSA1 TO SFBR
 967 
 968 at 0x000000f5 : */      0x72110000,0x00000000,
 969 /*
 970     MOVE SFBR TO SCRATCH1
 971 
 972 at 0x000000f7 : */      0x6a350000,0x00000000,
 973 /*
 974     MOVE DSA2 TO SFBR
 975 
 976 at 0x000000f9 : */      0x72120000,0x00000000,
 977 /*
 978     MOVE SFBR TO SCRATCH2
 979 
 980 at 0x000000fb : */      0x6a360000,0x00000000,
 981 /*
 982     MOVE DSA3 TO SFBR
 983 
 984 at 0x000000fd : */      0x72130000,0x00000000,
 985 /*
 986     MOVE SFBR TO SCRATCH3
 987 
 988 at 0x000000ff : */      0x6a370000,0x00000000,
 989 /*
 990 
 991     MOVE dmode_ncr_to_memory TO DMODE
 992 
 993 at 0x00000101 : */      0x78380000,0x00000000,
 994 /*
 995     MOVE MEMORY 4, addr_scratch, jump_to_dsa + 4
 996 
 997 at 0x00000103 : */      0xc0000004,0x00000000,0x00000424,
 998 /*
 999     MOVE dmode_memory_to_memory TO DMODE
1000 
1001 at 0x00000106 : */      0x78380000,0x00000000,
1002 /*
1003 jump_to_dsa:
1004     JUMP 0
1005 
1006 at 0x00000108 : */      0x80080000,0x00000000,
1007 /*
1008 
1009 
1010 
1011 
1012 
1013 munge_extended:
1014     CLEAR ACK
1015 
1016 at 0x0000010a : */      0x60000040,0x00000000,
1017 /*
1018     INT int_err_unexpected_phase, WHEN NOT MSG_IN
1019 
1020 at 0x0000010c : */      0x9f030000,0x00000000,
1021 /*
1022     MOVE 1, msg_buf + 1, WHEN MSG_IN
1023 
1024 at 0x0000010e : */      0x0f000001,0x00000001,
1025 /*
1026     JUMP munge_extended_2, IF 0x02
1027 
1028 at 0x00000110 : */      0x800c0002,0x00000458,
1029 /*
1030     JUMP munge_extended_3, IF 0x03 
1031 
1032 at 0x00000112 : */      0x800c0003,0x00000488,
1033 /*
1034     JUMP reject_message
1035 
1036 at 0x00000114 : */      0x80080000,0x000004b8,
1037 /*
1038 
1039 munge_extended_2:
1040     CLEAR ACK
1041 
1042 at 0x00000116 : */      0x60000040,0x00000000,
1043 /*
1044     MOVE 1, msg_buf + 2, WHEN MSG_IN
1045 
1046 at 0x00000118 : */      0x0f000001,0x00000002,
1047 /*
1048     JUMP reject_message, IF NOT 0x02    ; Must be WDTR
1049 
1050 at 0x0000011a : */      0x80040002,0x000004b8,
1051 /*
1052     CLEAR ACK
1053 
1054 at 0x0000011c : */      0x60000040,0x00000000,
1055 /*
1056     MOVE 1, msg_buf + 3, WHEN MSG_IN
1057 
1058 at 0x0000011e : */      0x0f000001,0x00000003,
1059 /*
1060     INT int_msg_wdtr
1061 
1062 at 0x00000120 : */      0x98080000,0x01000000,
1063 /*
1064 
1065 munge_extended_3:
1066     CLEAR ACK
1067 
1068 at 0x00000122 : */      0x60000040,0x00000000,
1069 /*
1070     MOVE 1, msg_buf + 2, WHEN MSG_IN
1071 
1072 at 0x00000124 : */      0x0f000001,0x00000002,
1073 /*
1074     JUMP reject_message, IF NOT 0x01    ; Must be SDTR
1075 
1076 at 0x00000126 : */      0x80040001,0x000004b8,
1077 /*
1078     CLEAR ACK
1079 
1080 at 0x00000128 : */      0x60000040,0x00000000,
1081 /*
1082     MOVE 2, msg_buf + 3, WHEN MSG_IN
1083 
1084 at 0x0000012a : */      0x0f000002,0x00000003,
1085 /*
1086     INT int_msg_sdtr
1087 
1088 at 0x0000012c : */      0x98080000,0x01010000,
1089 /*
1090 
1091 ENTRY reject_message
1092 reject_message:
1093     SET ATN
1094 
1095 at 0x0000012e : */      0x58000008,0x00000000,
1096 /*
1097     CLEAR ACK
1098 
1099 at 0x00000130 : */      0x60000040,0x00000000,
1100 /*
1101     MOVE 1, NCR53c7xx_msg_reject, WHEN MSG_OUT
1102 
1103 at 0x00000132 : */      0x0e000001,((unsigned long)&NCR53c7xx_msg_reject),
1104 /*
1105     RETURN
1106 
1107 at 0x00000134 : */      0x90080000,0x00000000,
1108 /*
1109 
1110 ENTRY accept_message
1111 accept_message:
1112     CLEAR ACK
1113 
1114 at 0x00000136 : */      0x60000040,0x00000000,
1115 /*
1116     RETURN
1117 
1118 at 0x00000138 : */      0x90080000,0x00000000,
1119 /*
1120 
1121 ENTRY respond_message
1122 msg_respond:
1123     SET ATN
1124 
1125 at 0x0000013a : */      0x58000008,0x00000000,
1126 /*
1127     CLEAR ACK
1128 
1129 at 0x0000013c : */      0x60000040,0x00000000,
1130 /*
1131     MOVE FROM dsa_msgout_other, WHEN MSG_OUT
1132 
1133 at 0x0000013e : */      0x1e000000,0x00000068,
1134 /*
1135     RETURN
1136 
1137 at 0x00000140 : */      0x90080000,0x00000000,
1138 /*
1139 
1140 ;
1141 ; command_complete
1142 ;
1143 ; PURPOSE : handle command termination when STATUS IN is detected by reading
1144 ;       a status byte followed by a command termination message. 
1145 ;
1146 ;       Normal termination results in an INTFLY instruction, and 
1147 ;       the host system can pick out which command terminated by 
1148 ;       examining the MESSAGE and STATUS buffers of all currently 
1149 ;       executing commands;
1150 ;
1151 ;       Abnormal (CHECK_CONDITION) termination results in an
1152 ;       int_err_check_condition interrupt so that a REQUEST SENSE
1153 ;       command can be issued out-of-order so that no other command
1154 ;       clears the contingent allegiance condition.
1155 ;       
1156 ;
1157 ; INPUTS : DSA - command        
1158 ;
1159 ; CALLS : OK
1160 ;
1161 ; EXITS : On successful termination, control is passed to schedule.
1162 ;       On abnormal termination, the user will usually modify the 
1163 ;       DSA fields and corresponding buffers and return control
1164 ;       to select.
1165 ;
1166 
1167 ENTRY command_complete
1168 command_complete:
1169     MOVE FROM dsa_status, WHEN STATUS
1170 
1171 at 0x00000142 : */      0x1b000000,0x00000060,
1172 /*
1173 
1174     MOVE SFBR TO SCRATCH0               ; Save status
1175 
1176 at 0x00000144 : */      0x6a340000,0x00000000,
1177 /*
1178 
1179 ENTRY command_complete_msgin
1180 command_complete_msgin:
1181     MOVE FROM dsa_msgin, WHEN MSG_IN
1182 
1183 at 0x00000146 : */      0x1f000000,0x00000058,
1184 /*
1185 ; Indicate that we should be expecting a disconnect
1186     MOVE SCNTL2 & 0x7f TO SCNTL2
1187 
1188 at 0x00000148 : */      0x7c027f00,0x00000000,
1189 /*
1190     CLEAR ACK
1191 
1192 at 0x0000014a : */      0x60000040,0x00000000,
1193 /*
1194 
1195     MOVE SCRATCH0 TO SFBR                       
1196 
1197 at 0x0000014c : */      0x72340000,0x00000000,
1198 /*
1199 
1200 ;
1201 ; The SCSI specification states that when a UNIT ATTENTION condition
1202 ; is pending, as indicated by a CHECK CONDITION status message,
1203 ; the target shall revert to asynchronous transfers.  Since
1204 ; synchronous transfers parameters are maintained on a per INITIATOR/TARGET 
1205 ; basis, and returning control to our scheduler could work on a command
1206 ; running on another lun on that target using the old parameters, we must
1207 ; interrupt the host processor to get them changed, or change them ourselves.
1208 ;
1209 ; Once SCSI-II tagged queueing is implemented, things will be even more
1210 ; hairy, since contingent allegiance conditions exist on a per-target/lun
1211 ; basis, and issuing a new command with a different tag would clear it.
1212 ; In these cases, we must interrupt the host processor to get a request 
1213 ; added to the HEAD of the queue with the request sense command, or we
1214 ; must automatically issue the request sense command.
1215 
1216 
1217 
1218 
1219     INTFLY
1220 
1221 at 0x0000014e : */      0x98180000,0x00000000,
1222 /*
1223 
1224     WAIT DISCONNECT
1225 
1226 at 0x00000150 : */      0x48000000,0x00000000,
1227 /*
1228 
1229     JUMP schedule
1230 
1231 at 0x00000152 : */      0x80080000,0x00000130,
1232 /*
1233 command_failed:
1234     WAIT DISCONNECT
1235 
1236 at 0x00000154 : */      0x48000000,0x00000000,
1237 /*
1238     INT int_err_check_condition
1239 
1240 at 0x00000156 : */      0x98080000,0x00030000,
1241 /*
1242 
1243 
1244 
1245 
1246 ;
1247 ; wait_reselect
1248 ;
1249 ; PURPOSE : This is essentially the idle routine, where control lands
1250 ;       when there are no new processes to schedule.  wait_reselect
1251 ;       waits for reselection, selection, and new commands.
1252 ;
1253 ;       When a successful reselection occurs, with the aid 
1254 ;       of fixed up code in each DSA, wait_reselect walks the 
1255 ;       reconnect_dsa_queue, asking each dsa if the target ID
1256 ;       and LUN match its.
1257 ;
1258 ;       If a match is found, a call is made back to reselected_ok,
1259 ;       which through the miracles of self modifying code, extracts
1260 ;       the found DSA from the reconnect_dsa_queue and then 
1261 ;       returns control to the DSAs thread of execution.
1262 ;
1263 ; INPUTS : NONE
1264 ;
1265 ; CALLS : OK
1266 ;
1267 ; MODIFIES : DSA,
1268 ;
1269 ; EXITS : On successful reselection, control is returned to the 
1270 ;       DSA which called reselected_ok.  If the WAIT RESELECT
1271 ;       was interrupted by a new commands arrival signaled by 
1272 ;       SIG_P, control is passed to schedule.  If the NCR is 
1273 ;       selected, the host system is interrupted with an 
1274 ;       int_err_selected which is usually responded to by
1275 ;       setting DSP to the target_abort address.
1276     
1277 wait_reselect:
1278 
1279 
1280 
1281     WAIT RESELECT wait_reselect_failed
1282 
1283 at 0x00000158 : */      0x50000000,0x0000067c,
1284 /*
1285 
1286 reselected:
1287     ; Read all data needed to reestablish the nexus - 
1288     MOVE 1, reselected_identify, WHEN MSG_IN
1289 
1290 at 0x0000015a : */      0x0f000001,0x00000000,
1291 /*
1292 
1293     ; Well add a jump to here after some how determining that 
1294     ; tagged queueing isn't in use on this device.
1295 reselected_notag:    
1296     MOVE MEMORY 1, NCR53c7xx_zero, reselected_tag
1297 
1298 at 0x0000015c : */      0xc0000001,((unsigned long)&NCR53c7xx_zero),0x00000000,
1299 /*
1300 
1301 
1302 
1303 
1304 
1305     ; Point DSA at the current head of the disconnected queue.
1306     MOVE dmode_memory_to_ncr  TO DMODE
1307 
1308 at 0x0000015f : */      0x78380000,0x00000000,
1309 /*
1310     MOVE MEMORY 4, reconnect_dsa_head, addr_scratch
1311 
1312 at 0x00000161 : */      0xc0000004,0x00000000,0x00000000,
1313 /*
1314     MOVE dmode_memory_to_memory TO DMODE
1315 
1316 at 0x00000164 : */      0x78380000,0x00000000,
1317 /*
1318     CALL scratch_to_dsa
1319 
1320 at 0x00000166 : */      0x88080000,0x00000800,
1321 /*
1322 
1323     ; Fix the update-next pointer so that the reconnect_dsa_head
1324     ; pointer is the one that will be updated if this DSA is a hit 
1325     ; and we remove it from the queue.
1326 
1327     MOVE MEMORY 4, reconnect_dsa_head, reselected_ok + 8
1328 
1329 at 0x00000168 : */      0xc0000004,0x00000000,0x00000660,
1330 /*
1331 
1332 ENTRY reselected_check_next
1333 reselected_check_next:
1334     ; Check for a NULL pointer.
1335     MOVE DSA0 TO SFBR
1336 
1337 at 0x0000016b : */      0x72100000,0x00000000,
1338 /*
1339     JUMP reselected_not_end, IF NOT 0
1340 
1341 at 0x0000016d : */      0x80040000,0x000005f4,
1342 /*
1343     MOVE DSA1 TO SFBR
1344 
1345 at 0x0000016f : */      0x72110000,0x00000000,
1346 /*
1347     JUMP reselected_not_end, IF NOT 0
1348 
1349 at 0x00000171 : */      0x80040000,0x000005f4,
1350 /*
1351     MOVE DSA2 TO SFBR
1352 
1353 at 0x00000173 : */      0x72120000,0x00000000,
1354 /*
1355     JUMP reselected_not_end, IF NOT 0
1356 
1357 at 0x00000175 : */      0x80040000,0x000005f4,
1358 /*
1359     MOVE DSA3 TO SFBR
1360 
1361 at 0x00000177 : */      0x72130000,0x00000000,
1362 /*
1363     JUMP reselected_not_end, IF NOT 0
1364 
1365 at 0x00000179 : */      0x80040000,0x000005f4,
1366 /*
1367     INT int_err_unexpected_reselect
1368 
1369 at 0x0000017b : */      0x98080000,0x00020000,
1370 /*
1371 
1372 reselected_not_end:
1373     MOVE DSA0 TO SFBR
1374 
1375 at 0x0000017d : */      0x72100000,0x00000000,
1376 /*
1377     ;
1378     ; XXX the ALU is only eight bits wide, and the assembler
1379     ; wont do the dirt work for us.  As long as dsa_check_reselect
1380     ; is negative, we need to sign extend with 1 bits to the full
1381     ; 32 bit width of the address.
1382     ;
1383     ; A potential work around would be to have a known alignment 
1384     ; of the DSA structure such that the base address plus 
1385     ; dsa_check_reselect doesn't require carrying from bytes 
1386     ; higher than the LSB.
1387     ;
1388 
1389     MOVE SFBR + dsa_check_reselect TO SCRATCH0
1390 
1391 at 0x0000017f : */      0x6e340000,0x00000000,
1392 /*
1393     MOVE DSA1 TO SFBR
1394 
1395 at 0x00000181 : */      0x72110000,0x00000000,
1396 /*
1397     MOVE SFBR + 0xff TO SCRATCH1 WITH CARRY
1398 
1399 at 0x00000183 : */      0x6f35ff00,0x00000000,
1400 /*
1401     MOVE DSA2 TO SFBR
1402 
1403 at 0x00000185 : */      0x72120000,0x00000000,
1404 /*
1405     MOVE SFBR + 0xff TO SCRATCH2 WITH CARRY
1406 
1407 at 0x00000187 : */      0x6f36ff00,0x00000000,
1408 /*
1409     MOVE DSA3 TO SFBR
1410 
1411 at 0x00000189 : */      0x72130000,0x00000000,
1412 /*
1413     MOVE SFBR + 0xff TO SCRATCH3 WITH CARRY
1414 
1415 at 0x0000018b : */      0x6f37ff00,0x00000000,
1416 /*
1417 
1418     MOVE dmode_ncr_to_memory TO DMODE
1419 
1420 at 0x0000018d : */      0x78380000,0x00000000,
1421 /*
1422     MOVE MEMORY 4, addr_scratch, reselected_check + 4
1423 
1424 at 0x0000018f : */      0xc0000004,0x00000000,0x00000654,
1425 /*
1426     MOVE dmode_memory_to_memory TO DMODE
1427 
1428 at 0x00000192 : */      0x78380000,0x00000000,
1429 /*
1430 reselected_check:
1431     JUMP 0
1432 
1433 at 0x00000194 : */      0x80080000,0x00000000,
1434 /*
1435 
1436 
1437 ;
1438 ;
1439 reselected_ok:
1440     MOVE MEMORY 4, 0, 0                         ; Patched : first word
1441 
1442 at 0x00000196 : */      0xc0000004,0x00000000,0x00000000,
1443 /*
1444                                                 ;       is this successful 
1445                                                 ;       dsa_next
1446                                                 ; Second word is 
1447                                                 ;       unsuccessful dsa_next
1448     CLEAR ACK                                   ; Accept last message
1449 
1450 at 0x00000199 : */      0x60000040,0x00000000,
1451 /*
1452     RETURN                                      ; Return control to where
1453 
1454 at 0x0000019b : */      0x90080000,0x00000000,
1455 /*
1456 
1457 
1458 
1459 
1460 selected:
1461     INT int_err_selected;
1462 
1463 at 0x0000019d : */      0x98080000,0x00010000,
1464 /*
1465 
1466 ;
1467 ; A select or reselect failure can be caused by one of two conditions : 
1468 ; 1.  SIG_P was set.  This will be the case if the user has written
1469 ;       a new value to a previously NULL head of the issue queue.
1470 ;
1471 ; 2.  The NCR53c810 was selected or reselected by another device.
1472 ; 
1473 
1474 wait_reselect_failed:
1475 ; Reading CTEST2 clears the SIG_P bit in the ISTAT register.
1476     MOVE CTEST2 & 0x40 TO SFBR  
1477 
1478 at 0x0000019f : */      0x741a4000,0x00000000,
1479 /*
1480     JUMP selected, IF NOT 0x40
1481 
1482 at 0x000001a1 : */      0x80040040,0x00000674,
1483 /*
1484     JUMP schedule
1485 
1486 at 0x000001a3 : */      0x80080000,0x00000130,
1487 /*
1488 
1489 select_failed:
1490     MOVE ISTAT & 0x20 TO SFBR
1491 
1492 at 0x000001a5 : */      0x74142000,0x00000000,
1493 /*
1494     JUMP reselected, IF NOT 0x20
1495 
1496 at 0x000001a7 : */      0x80040020,0x00000568,
1497 /*
1498     MOVE ISTAT & 0xdf TO ISTAT
1499 
1500 at 0x000001a9 : */      0x7c14df00,0x00000000,
1501 /*
1502     JUMP schedule
1503 
1504 at 0x000001ab : */      0x80080000,0x00000130,
1505 /*
1506 
1507 ;
1508 ; test_1
1509 ; test_2
1510 ;
1511 ; PURPOSE : run some verification tests on the NCR.  test_1
1512 ;       copies test_src to test_dest and interrupts the host
1513 ;       processor, testing for cache coherency and interrupt
1514 ;       problems in the processes.
1515 ;
1516 ;       test_2 runs a command with offsets relative to the 
1517 ;       DSA on entry, and is useful for miscellaneous experimentation.
1518 ;
1519 
1520 ; Verify that interrupts are working correctly and that we don't 
1521 ; have a cache invalidation problem.
1522 
1523 ABSOLUTE test_src = 0, test_dest = 0
1524 ENTRY test_1
1525 test_1:
1526     MOVE MEMORY 4, test_src, test_dest
1527 
1528 at 0x000001ad : */      0xc0000004,0x00000000,0x00000000,
1529 /*
1530     INT int_test_1
1531 
1532 at 0x000001b0 : */      0x98080000,0x04000000,
1533 /*
1534 
1535 ;
1536 ; Run arbitrary commands, with test code establishing a DSA
1537 ;
1538  
1539 ENTRY test_2
1540 test_2:
1541     CLEAR TARGET
1542 
1543 at 0x000001b2 : */      0x60000200,0x00000000,
1544 /*
1545     SELECT ATN FROM 0, test_2_fail
1546 
1547 at 0x000001b4 : */      0x43000000,0x00000720,
1548 /*
1549     JUMP test_2_msgout, WHEN MSG_OUT
1550 
1551 at 0x000001b6 : */      0x860b0000,0x000006e0,
1552 /*
1553 ENTRY test_2_msgout
1554 test_2_msgout:
1555     MOVE FROM 8, WHEN MSG_OUT
1556 
1557 at 0x000001b8 : */      0x1e000000,0x00000008,
1558 /*
1559     MOVE FROM 16, WHEN CMD 
1560 
1561 at 0x000001ba : */      0x1a000000,0x00000010,
1562 /*
1563     MOVE FROM 24, WHEN DATA_IN
1564 
1565 at 0x000001bc : */      0x19000000,0x00000018,
1566 /*
1567     MOVE FROM 32, WHEN STATUS
1568 
1569 at 0x000001be : */      0x1b000000,0x00000020,
1570 /*
1571     MOVE FROM 40, WHEN MSG_IN
1572 
1573 at 0x000001c0 : */      0x1f000000,0x00000028,
1574 /*
1575     MOVE SCNTL2 & 0x7f TO SCNTL2
1576 
1577 at 0x000001c2 : */      0x7c027f00,0x00000000,
1578 /*
1579     CLEAR ACK
1580 
1581 at 0x000001c4 : */      0x60000040,0x00000000,
1582 /*
1583     WAIT DISCONNECT
1584 
1585 at 0x000001c6 : */      0x48000000,0x00000000,
1586 /*
1587 test_2_fail:
1588     INT int_test_2
1589 
1590 at 0x000001c8 : */      0x98080000,0x04010000,
1591 /*
1592 
1593 ENTRY debug_break
1594 debug_break:
1595     INT int_debug_break
1596 
1597 at 0x000001ca : */      0x98080000,0x03000000,
1598 /*
1599 
1600 ;
1601 ; initiator_abort
1602 ; target_abort
1603 ;
1604 ; PURPOSE : Abort the currently established nexus from with initiator
1605 ;       or target mode.
1606 ;
1607 ;  
1608 
1609 ENTRY target_abort
1610 target_abort:
1611     SET TARGET
1612 
1613 at 0x000001cc : */      0x58000200,0x00000000,
1614 /*
1615     DISCONNECT
1616 
1617 at 0x000001ce : */      0x48000000,0x00000000,
1618 /*
1619     CLEAR TARGET
1620 
1621 at 0x000001d0 : */      0x60000200,0x00000000,
1622 /*
1623     JUMP schedule
1624 
1625 at 0x000001d2 : */      0x80080000,0x00000130,
1626 /*
1627     
1628 ENTRY initiator_abort
1629 initiator_abort:
1630     SET ATN
1631 
1632 at 0x000001d4 : */      0x58000008,0x00000000,
1633 /*
1634 ; In order to abort the currently established nexus, we 
1635 ; need to source/sink up to one byte of data in any SCSI phase, 
1636 ; since the phase cannot change until REQ transitions 
1637 ; false->true
1638     JUMP no_eat_cmd, WHEN NOT CMD
1639 
1640 at 0x000001d6 : */      0x82030000,0x00000768,
1641 /*
1642     MOVE 1, NCR53c7xx_zero, WHEN CMD
1643 
1644 at 0x000001d8 : */      0x0a000001,((unsigned long)&NCR53c7xx_zero),
1645 /*
1646 no_eat_cmd:
1647     JUMP no_eat_msg, WHEN NOT MSG_IN
1648 
1649 at 0x000001da : */      0x87030000,0x00000778,
1650 /*
1651     MOVE 1, NCR53c7xx_sink, WHEN MSG_IN
1652 
1653 at 0x000001dc : */      0x0f000001,((unsigned long)&NCR53c7xx_sink),
1654 /*
1655 no_eat_msg:
1656     JUMP no_eat_data, WHEN NOT DATA_IN
1657 
1658 at 0x000001de : */      0x81030000,0x00000788,
1659 /*
1660     MOVE 1, NCR53c7xx_sink, WHEN DATA_IN
1661 
1662 at 0x000001e0 : */      0x09000001,((unsigned long)&NCR53c7xx_sink),
1663 /*
1664 no_eat_data:
1665     JUMP no_eat_status, WHEN NOT STATUS
1666 
1667 at 0x000001e2 : */      0x83030000,0x00000798,
1668 /*
1669     MOVE 1, NCR53c7xx_sink, WHEN STATUS
1670 
1671 at 0x000001e4 : */      0x0b000001,((unsigned long)&NCR53c7xx_sink),
1672 /*
1673 no_eat_status:
1674     JUMP no_source_data, WHEN NOT DATA_OUT
1675 
1676 at 0x000001e6 : */      0x80030000,0x000007a8,
1677 /*
1678     MOVE 1, NCR53c7xx_zero, WHEN DATA_OUT
1679 
1680 at 0x000001e8 : */      0x08000001,((unsigned long)&NCR53c7xx_zero),
1681 /*
1682 no_source_data:
1683 ;
1684 ; If DSP points here, and a phase mismatch is encountered, we need to 
1685 ; do a bus reset.
1686 ;
1687     MOVE 1, NCR53c7xx_msg_abort, WHEN MSG_OUT
1688 
1689 at 0x000001ea : */      0x0e000001,((unsigned long)&NCR53c7xx_msg_abort),
1690 /*
1691     INT int_norm_aborted
1692 
1693 at 0x000001ec : */      0x98080000,0x02040000,
1694 /*
1695 
1696 ;
1697 ; dsa_to_scratch
1698 ; scratch_to_dsa
1699 ;
1700 ; PURPOSE :
1701 ;       The NCR chips cannot do a move memory instruction with the DSA register 
1702 ;       as the source or destination.  So, we provide a couple of subroutines
1703 ;       that let us switch between the DSA register and scratch register.
1704 ;
1705 ;       Memory moves to/from the DSPS  register also don't work, but we 
1706 ;       don't use them.
1707 ;
1708 ;
1709 
1710  
1711 dsa_to_scratch:
1712     MOVE DSA0 TO SFBR
1713 
1714 at 0x000001ee : */      0x72100000,0x00000000,
1715 /*
1716     MOVE SFBR TO SCRATCH0
1717 
1718 at 0x000001f0 : */      0x6a340000,0x00000000,
1719 /*
1720     MOVE DSA1 TO SFBR
1721 
1722 at 0x000001f2 : */      0x72110000,0x00000000,
1723 /*
1724     MOVE SFBR TO SCRATCH1
1725 
1726 at 0x000001f4 : */      0x6a350000,0x00000000,
1727 /*
1728     MOVE DSA2 TO SFBR
1729 
1730 at 0x000001f6 : */      0x72120000,0x00000000,
1731 /*
1732     MOVE SFBR TO SCRATCH2
1733 
1734 at 0x000001f8 : */      0x6a360000,0x00000000,
1735 /*
1736     MOVE DSA3 TO SFBR
1737 
1738 at 0x000001fa : */      0x72130000,0x00000000,
1739 /*
1740     MOVE SFBR TO SCRATCH3
1741 
1742 at 0x000001fc : */      0x6a370000,0x00000000,
1743 /*
1744     RETURN
1745 
1746 at 0x000001fe : */      0x90080000,0x00000000,
1747 /*
1748 
1749 scratch_to_dsa:
1750     MOVE SCRATCH0 TO SFBR
1751 
1752 at 0x00000200 : */      0x72340000,0x00000000,
1753 /*
1754     MOVE SFBR TO DSA0
1755 
1756 at 0x00000202 : */      0x6a100000,0x00000000,
1757 /*
1758     MOVE SCRATCH1 TO SFBR
1759 
1760 at 0x00000204 : */      0x72350000,0x00000000,
1761 /*
1762     MOVE SFBR TO DSA1
1763 
1764 at 0x00000206 : */      0x6a110000,0x00000000,
1765 /*
1766     MOVE SCRATCH2 TO SFBR
1767 
1768 at 0x00000208 : */      0x72360000,0x00000000,
1769 /*
1770     MOVE SFBR TO DSA2
1771 
1772 at 0x0000020a : */      0x6a120000,0x00000000,
1773 /*
1774     MOVE SCRATCH3 TO SFBR
1775 
1776 at 0x0000020c : */      0x72370000,0x00000000,
1777 /*
1778     MOVE SFBR TO DSA3
1779 
1780 at 0x0000020e : */      0x6a130000,0x00000000,
1781 /*
1782     RETURN
1783 
1784 at 0x00000210 : */      0x90080000,0x00000000,
1785 };
1786 
1787 #define A_addr_scratch  0x00000000
1788 unsigned long A_addr_scratch_used[] = {
1789         0x00000007,
1790         0x0000003a,
1791         0x00000046,
1792         0x00000050,
1793         0x0000007a,
1794         0x000000a8,
1795         0x000000be,
1796         0x00000104,
1797         0x00000163,
1798         0x00000190,
1799 };
1800 
1801 #define A_addr_sfbr     0x00000000
1802 unsigned long A_addr_sfbr_used[] = {
1803         0x00000016,
1804 };
1805 
1806 #define A_addr_temp     0x00000000
1807 unsigned long A_addr_temp_used[] = {
1808         0x00000027,
1809 };
1810 
1811 #define A_dmode_memory_to_memory        0x00000000
1812 unsigned long A_dmode_memory_to_memory_used[] = {
1813         0x00000008,
1814         0x00000019,
1815         0x00000029,
1816         0x0000003c,
1817         0x00000048,
1818         0x00000051,
1819         0x0000007c,
1820         0x000000aa,
1821         0x000000c0,
1822         0x00000106,
1823         0x00000164,
1824         0x00000192,
1825 };
1826 
1827 #define A_dmode_memory_to_ncr   0x00000000
1828 unsigned long A_dmode_memory_to_ncr_used[] = {
1829         0x00000003,
1830         0x00000012,
1831         0x0000004c,
1832         0x0000015f,
1833 };
1834 
1835 #define A_dmode_ncr_to_memory   0x00000000
1836 unsigned long A_dmode_ncr_to_memory_used[] = {
1837         0x00000024,
1838         0x00000037,
1839         0x00000043,
1840         0x00000077,
1841         0x000000a5,
1842         0x000000bb,
1843         0x00000101,
1844         0x0000018d,
1845 };
1846 
1847 #define A_dmode_ncr_to_ncr      0x00000000
1848 unsigned long A_dmode_ncr_to_ncr_used[] = {
1849 };
1850 
1851 #define A_dsa_check_reselect    0x00000000
1852 unsigned long A_dsa_check_reselect_used[] = {
1853         0x0000017f,
1854 };
1855 
1856 #define A_dsa_cmdout    0x00000048
1857 unsigned long A_dsa_cmdout_used[] = {
1858         0x0000008c,
1859 };
1860 
1861 #define A_dsa_cmnd      0x00000038
1862 unsigned long A_dsa_cmnd_used[] = {
1863 };
1864 
1865 #define A_dsa_datain    0x00000054
1866 unsigned long A_dsa_datain_used[] = {
1867         0x000000b3,
1868 };
1869 
1870 #define A_dsa_dataout   0x00000050
1871 unsigned long A_dsa_dataout_used[] = {
1872         0x0000009d,
1873 };
1874 
1875 #define A_dsa_end       0x00000070
1876 unsigned long A_dsa_end_used[] = {
1877 };
1878 
1879 #define A_dsa_fields_start      0x00000024
1880 unsigned long A_dsa_fields_start_used[] = {
1881 };
1882 
1883 #define A_dsa_msgin     0x00000058
1884 unsigned long A_dsa_msgin_used[] = {
1885         0x00000147,
1886 };
1887 
1888 #define A_dsa_msgout    0x00000040
1889 unsigned long A_dsa_msgout_used[] = {
1890         0x0000006c,
1891 };
1892 
1893 #define A_dsa_msgout_other      0x00000068
1894 unsigned long A_dsa_msgout_other_used[] = {
1895         0x0000013f,
1896 };
1897 
1898 #define A_dsa_next      0x00000030
1899 unsigned long A_dsa_next_used[] = {
1900         0x0000002f,
1901         0x0000006f,
1902 };
1903 
1904 #define A_dsa_select    0x0000003c
1905 unsigned long A_dsa_select_used[] = {
1906         0x00000067,
1907 };
1908 
1909 #define A_dsa_status    0x00000060
1910 unsigned long A_dsa_status_used[] = {
1911         0x00000143,
1912 };
1913 
1914 #define A_dsa_temp_dsa_next     0x00000000
1915 unsigned long A_dsa_temp_dsa_next_used[] = {
1916         0x00000001,
1917         0x00000006,
1918         0x0000001c,
1919 };
1920 
1921 #define A_dsa_temp_jump_resume  0x00000000
1922 unsigned long A_dsa_temp_jump_resume_used[] = {
1923         0x00000028,
1924 };
1925 
1926 #define A_dsa_temp_lun  0x00000000
1927 unsigned long A_dsa_temp_lun_used[] = {
1928         0x00000017,
1929 };
1930 
1931 #define A_dsa_temp_sync 0x00000000
1932 unsigned long A_dsa_temp_sync_used[] = {
1933         0x00000021,
1934 };
1935 
1936 #define A_dsa_temp_target       0x00000000
1937 unsigned long A_dsa_temp_target_used[] = {
1938         0x00000010,
1939 };
1940 
1941 #define A_int_debug_break       0x03000000
1942 unsigned long A_int_debug_break_used[] = {
1943         0x000001cb,
1944 };
1945 
1946 #define A_int_debug_dsa_loaded  0x03030000
1947 unsigned long A_int_debug_dsa_loaded_used[] = {
1948 };
1949 
1950 #define A_int_debug_head        0x03050000
1951 unsigned long A_int_debug_head_used[] = {
1952 };
1953 
1954 #define A_int_debug_idle        0x03020000
1955 unsigned long A_int_debug_idle_used[] = {
1956 };
1957 
1958 #define A_int_debug_reselected  0x03040000
1959 unsigned long A_int_debug_reselected_used[] = {
1960 };
1961 
1962 #define A_int_debug_scheduled   0x03010000
1963 unsigned long A_int_debug_scheduled_used[] = {
1964 };
1965 
1966 #define A_int_err_check_condition       0x00030000
1967 unsigned long A_int_err_check_condition_used[] = {
1968         0x00000157,
1969 };
1970 
1971 #define A_int_err_no_phase      0x00040000
1972 unsigned long A_int_err_no_phase_used[] = {
1973 };
1974 
1975 #define A_int_err_selected      0x00010000
1976 unsigned long A_int_err_selected_used[] = {
1977         0x0000019e,
1978 };
1979 
1980 #define A_int_err_unexpected_phase      0x00000000
1981 unsigned long A_int_err_unexpected_phase_used[] = {
1982         0x00000084,
1983         0x0000008a,
1984         0x0000008e,
1985         0x00000092,
1986         0x000000c8,
1987         0x000000cc,
1988         0x000000ce,
1989         0x000000d0,
1990         0x0000010d,
1991 };
1992 
1993 #define A_int_err_unexpected_reselect   0x00020000
1994 unsigned long A_int_err_unexpected_reselect_used[] = {
1995         0x0000017c,
1996 };
1997 
1998 #define A_int_msg_1     0x01020000
1999 unsigned long A_int_msg_1_used[] = {
2000         0x000000e2,
2001         0x000000e4,
2002 };
2003 
2004 #define A_int_msg_sdtr  0x01010000
2005 unsigned long A_int_msg_sdtr_used[] = {
2006         0x0000012d,
2007 };
2008 
2009 #define A_int_msg_wdtr  0x01000000
2010 unsigned long A_int_msg_wdtr_used[] = {
2011         0x00000121,
2012 };
2013 
2014 #define A_int_norm_aborted      0x02040000
2015 unsigned long A_int_norm_aborted_used[] = {
2016         0x000001ed,
2017 };
2018 
2019 #define A_int_norm_command_complete     0x02020000
2020 unsigned long A_int_norm_command_complete_used[] = {
2021 };
2022 
2023 #define A_int_norm_disconnected 0x02030000
2024 unsigned long A_int_norm_disconnected_used[] = {
2025 };
2026 
2027 #define A_int_norm_reselect_complete    0x02010000
2028 unsigned long A_int_norm_reselect_complete_used[] = {
2029 };
2030 
2031 #define A_int_norm_reset        0x02050000
2032 unsigned long A_int_norm_reset_used[] = {
2033 };
2034 
2035 #define A_int_norm_select_complete      0x02000000
2036 unsigned long A_int_norm_select_complete_used[] = {
2037 };
2038 
2039 #define A_int_test_1    0x04000000
2040 unsigned long A_int_test_1_used[] = {
2041         0x000001b1,
2042 };
2043 
2044 #define A_int_test_2    0x04010000
2045 unsigned long A_int_test_2_used[] = {
2046         0x000001c9,
2047 };
2048 
2049 #define A_int_test_3    0x04020000
2050 unsigned long A_int_test_3_used[] = {
2051 };
2052 
2053 #define A_issue_dsa_head        0x00000000
2054 unsigned long A_issue_dsa_head_used[] = {
2055         0x0000004f,
2056         0x00000080,
2057 };
2058 
2059 #define A_msg_buf       0x00000000
2060 unsigned long A_msg_buf_used[] = {
2061         0x000000d6,
2062         0x0000010f,
2063         0x00000119,
2064         0x0000011f,
2065         0x00000125,
2066         0x0000012b,
2067 };
2068 
2069 #define A_reconnect_dsa_head    0x00000000
2070 unsigned long A_reconnect_dsa_head_used[] = {
2071         0x0000003f,
2072         0x00000047,
2073         0x00000162,
2074         0x00000169,
2075 };
2076 
2077 #define A_reselected_identify   0x00000000
2078 unsigned long A_reselected_identify_used[] = {
2079         0x00000015,
2080         0x0000015b,
2081 };
2082 
2083 #define A_reselected_tag        0x00000000
2084 unsigned long A_reselected_tag_used[] = {
2085         0x0000015e,
2086 };
2087 
2088 #define A_test_dest     0x00000000
2089 unsigned long A_test_dest_used[] = {
2090         0x000001af,
2091 };
2092 
2093 #define A_test_src      0x00000000
2094 unsigned long A_test_src_used[] = {
2095         0x000001ae,
2096 };
2097 
2098 #define Ent_accept_message      0x000004d8
2099 #define Ent_cmdout_cmdout       0x0000022c
2100 #define Ent_command_complete    0x00000508
2101 #define Ent_command_complete_msgin      0x00000518
2102 #define Ent_debug_break 0x00000728
2103 #define Ent_dsa_code_check_reselect     0x00000038
2104 #define Ent_dsa_code_template   0x00000000
2105 #define Ent_dsa_code_template_end       0x000000b4
2106 #define Ent_dsa_jump_resume     0x00000088
2107 #define Ent_dsa_schedule        0x000000b4
2108 #define Ent_dsa_zero    0x00000090
2109 #define Ent_initiator_abort     0x00000750
2110 #define Ent_msg_in      0x00000354
2111 #define Ent_other_transfer      0x0000031c
2112 #define Ent_reject_message      0x000004b8
2113 #define Ent_reselected_check_next       0x000005ac
2114 #define Ent_respond_message     0x00000000
2115 #define Ent_schedule    0x00000130
2116 #define Ent_select      0x00000194
2117 #define Ent_select_msgout       0x000001ac
2118 #define Ent_target_abort        0x00000730
2119 #define Ent_test_1      0x000006b4
2120 #define Ent_test_2      0x000006c8
2121 #define Ent_test_2_msgout       0x000006e0
2122 unsigned long LABELPATCHES[] = {
2123         0x00000002,
2124         0x0000000b,
2125         0x0000000d,
2126         0x0000001d,
2127         0x0000001f,
2128         0x0000002c,
2129         0x0000002e,
2130         0x0000003b,
2131         0x00000042,
2132         0x00000054,
2133         0x00000058,
2134         0x0000005c,
2135         0x00000060,
2136         0x00000064,
2137         0x00000068,
2138         0x0000006a,
2139         0x0000006e,
2140         0x0000007b,
2141         0x00000082,
2142         0x00000086,
2143         0x00000088,
2144         0x00000090,
2145         0x00000094,
2146         0x00000096,
2147         0x00000098,
2148         0x0000009a,
2149         0x0000009c,
2150         0x000000a9,
2151         0x000000ae,
2152         0x000000b2,
2153         0x000000bf,
2154         0x000000c4,
2155         0x000000ca,
2156         0x000000d2,
2157         0x000000d4,
2158         0x000000d8,
2159         0x000000da,
2160         0x000000dc,
2161         0x000000de,
2162         0x000000e0,
2163         0x000000e6,
2164         0x000000e8,
2165         0x00000105,
2166         0x00000111,
2167         0x00000113,
2168         0x00000115,
2169         0x0000011b,
2170         0x00000127,
2171         0x00000153,
2172         0x00000159,
2173         0x00000167,
2174         0x0000016a,
2175         0x0000016e,
2176         0x00000172,
2177         0x00000176,
2178         0x0000017a,
2179         0x00000191,
2180         0x000001a2,
2181         0x000001a4,
2182         0x000001a8,
2183         0x000001ac,
2184         0x000001b5,
2185         0x000001b7,
2186         0x000001d3,
2187         0x000001d7,
2188         0x000001db,
2189         0x000001df,
2190         0x000001e3,
2191         0x000001e7,
2192 };
2193 
2194 unsigned long INSTRUCTIONS      = 0x000000fe;
2195 unsigned long PATCHES   = 0x00000045;

/* [previous][next][first][last][top][bottom][index][help] */