1 /* Definitions for the 3Com 3c503 Etherlink 2. */ 2 /* This file is distributed under the GPL. 3 Some of these names and comments are from the Crynwr packet drivers. */ 4 5 #define EL2H (dev->base_addr + 0x400) 6 #define EL2L (dev->base_addr) 7 8 /* Shared memory management parameters */ 9 10 #define EL2SM_START_PG (0x20) /* First page of TX buffer */ 11 #define EL2SM_STOP_PG (0x40) /* Last page +1 of RX ring */ 12 13 /* 3Com 3c503 ASIC registers */ 14 #define E33G_STARTPG (EL2H+0) /* Start page, must match EN0_STARTPG */ 15 #define E33G_STOPPG (EL2H+1) /* Stop page, must match EN0_STOPPG */ 16 #define E33G_DRQCNT (EL2H+2) /* DMA burst count */ 17 #define E33G_IOBASE (EL2H+3) /* Read of I/O base jumpers. */ 18 /* (non-useful, but it also appears at the end of EPROM space) */ 19 #define E33G_ROMBASE (EL2H+4) /* Read of memory base jumpers. */ 20 #define E33G_GACFR (EL2H+5) /* Config/setup bits for the ASIC GA */ 21 #define E33G_CNTRL (EL2H+6) /* Board's main control register */ 22 #define E33G_STATUS (EL2H+7) /* Status on completions. */ 23 #define E33G_IDCFR (EL2H+8) /* Interrupt/DMA config register */ 24 /* (Which IRQ to assert, DMA chan to use) */ 25 #define E33G_DMAAH (EL2H+9) /* High byte of DMA address reg */ 26 #define E33G_DMAAL (EL2H+10) /* Low byte of DMA address reg */ 27 /* "Vector pointer" - if this address matches a read, the EPROM (rather than 28 shared RAM) is mapped into memory space. */ 29 #define E33G_VP2 (EL2H+11) 30 #define E33G_VP1 (EL2H+12) 31 #define E33G_VP0 (EL2H+13) 32 #define E33G_FIFOH (EL2H+14) /* FIFO for programmed I/O moves */ 33 #define E33G_FIFOL (EL2H+15) /* ... low byte of above. */ 34 35 /* Bits in E33G_CNTRL register: */ 36 37 #define ECNTRL_RESET (0x01) /* Software reset of the ASIC and 8390 */ 38 #define ECNTRL_THIN (0x02) /* Onboard xcvr enable, AUI disable */ 39 #define ECNTRL_AUI (0x00) /* Onboard xcvr disable, AUI enable */ 40 #define ECNTRL_SAPROM (0x04) /* Map the station address prom */ 41 #define ECNTRL_DBLBFR (0x20) /* FIFO configuration bit */ 42 #define ECNTRL_OUTPUT (0x40) /* PC-to-3C503 direction if 1 */ 43 #define ECNTRL_INPUT (0x00) /* 3C503-to-PC direction if 0 */ 44 #define ECNTRL_START (0x80) /* Start the DMA logic */ 45 46 /* Bits in E33G_STATUS register: */ 47 48 #define ESTAT_DPRDY (0x80) /* Data port (of FIFO) ready */ 49 #define ESTAT_UFLW (0x40) /* Tried to read FIFO when it was empty */ 50 #define ESTAT_OFLW (0x20) /* Tried to write FIFO when it was full */ 51 #define ESTAT_DTC (0x10) /* Terminal Count from PC bus DMA logic */ 52 #define ESTAT_DIP (0x08) /* DMA In Progress */ 53 54 /* Bits in E33G_GACFR register: */ 55 56 #define EGACFR_NORM (0x49) /* Enable 8K shared mem, no DMA TC int */ 57 #define EGACFR_IRQOFF (0xc9) /* Above, and disable 8390 IRQ line */ 58 59 /* End of 3C503 parameter definitions */