This source file includes following definitions.
- print_opcode
- print_opcode
- print_command
- print_status
- print_msg
- print_msg
- print_sense
1
2
3
4
5
6 #include <linux/config.h>
7 #ifdef CONFIG_SCSI
8 #include "../blk.h"
9 #include <linux/kernel.h>
10 #include "scsi.h"
11 static const char reserved[] = "RESERVED";
12 static const char unknown[] = "UNKNOWN";
13 static const char vendor[] = "VENDOR SPECIFIC";
14
15 #define CONST_COMMAND 0x01
16 #define CONST_STATUS 0x02
17 #define CONST_SENSE 0x04
18 #define CONST_XSENSE 0x08
19
20 #ifdef CONFIG_SCSI_CONSTANTS
21 #ifdef CONSTANTS
22 #undef CONSTANTS
23 #endif
24 #define CONSTANTS (CONST_CMD | CONST_STATUS | CONST_SENSE | CONST_XSENSE)
25 #endif
26
27 #if (CONSTANTS & CONST_COMMAND)
28 static const char * group_0_commands[] = {
29 "Test Unit Ready", "Rezero Unit", unknown, "Request Sense",
30 "Format Unit", "Read Block Limits", unknown, "Reasssign Blocks",
31 "Read (6)", unknown, "Write (6)", "Seek (6)", unknown, unknown,
32 unknown, "Read Reverse", "Write Filemarks", "Space", "Inquiry",
33 unknown, "Recover Buffered Data", "Mode Select", "Reserve",
34 "Release", "Copy", "Erase", "Mode Sense", "Start/Stop Unit",
35 "Receive Diagnostic", "Send Diagnostic",
36 "Prevent/Allow Medium Removal", unknown,
37 };
38
39
40 static const char *group_1_commands[] = {
41 unknown, unknown, unknown,
42 unknown, unknown, "Read Capacity", unknown, unknown, "Read (10)",
43 unknown, "Write (10)", "Seek (10)", unknown, unknown,
44 "Write Verify","Verify", "Search High", "Search Equal",
45 "Search Low", "Set Limits", "Prefetch or Read Position",
46 "Synchronize Cache","Lock/Unlock Cache", "Read Deffect Data",
47 unknown, "Compare","Copy Verify", "Write Buffer", "Read Buffer",
48 unknown, "Read Long", unknown,
49 };
50
51
52 static const char *group_2_commands[] = {
53 "Change Definition", unknown,
54 unknown, unknown, unknown, unknown, unknown, unknown, unknown,
55 unknown, unknown, unknown, "Log Select", "Log Sense", unknown,
56 unknown, unknown, unknown, unknown, unknown, "Mode Select (10)",
57 unknown, unknown, unknown, unknown, "Mode Sense (10)", unknown,
58 unknown, unknown, unknown,
59 };
60
61
62
63 #define group(opcode) (((opcode) >> 5) & 7)
64
65 #define RESERVED_GROUP 0
66 #define VENDOR_GROUP 1
67 #define NOTEXT_GROUP 2
68
69 static const char **commands[] = {
70 group_0_commands, group_1_commands, group_2_commands,
71 (const char **) RESERVED_GROUP, (const char **) RESERVED_GROUP,
72 (const char **) NOTEXT_GROUP, (const char **) VENDOR_GROUP,
73 (const char **) VENDOR_GROUP};
74
75
76 static void print_opcode(int opcode) {
77 char **table = commands[ group(opcode) ];
78 switch ((int) table) {
79 case RESERVED_GROUP:
80 printk("%s(0x%02x) ", reserved, opcode);
81 break;
82 case NOTEXT_GROUP:
83 printk("%s(0x%02x) ", unknown, opcode);
84 break;
85 case VENDOR_GROUP:
86 printk("%s(0x%02x) ", vendor, opcode);
87 break;
88 default:
89 printk("%s ",table[opcode & 0x31]);
90 }
91 }
92 #else
93 static void print_opcode(int opcode) {
94 printk("0x%02x ", opcode);
95 }
96 #endif
97
98 void print_command (unsigned char *command) {
99 int i,s;
100 print_opcode(command[0]);
101 for ( i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i)
102 printk("%02x ", command[i]);
103 printk("\n");
104 }
105
106 #if (CONSTANTS & CONST_STATUS)
107 static const char * statuses[] = {
108 "Good", "Check Condition", "Condition Good", unknown, "Busy",
109 unknown, unknown, unknown, "Intermediate Good", unknown,
110 "Interemediate Good", unknown, "Reservation Conflict", unknown,
111 unknown, unknown,
112 };
113 #endif
114
115 void print_status (int status) {
116 status = (status >> 1) & 0xf;
117 #if (CONSTANTS & CONST_STATUS)
118 printk("%s ",statuses[status]);
119 #else
120 printk("0x%0x ", status);
121 #endif
122 }
123
124 #if (CONSTANTS & CONST_MSG)
125 static const char * msgs[] = {
126 };
127 void print_msg (int msg) {
128 printk("%s ", msgs[msg]);
129 }
130 #else
131 void print_msg (int msg) {
132 printk("0x%02x ", msg);
133 }
134 #endif
135
136 #if (CONSTANTS & CONST_XSENSE)
137 #define D 0x001
138 #define T 0x002
139 #define L 0x004
140 #define P 0x008
141 #define W 0x010
142 #define R 0x020
143 #define S 0x040
144 #define O 0x080
145 #define M 0x100
146 #define C 0x200
147
148 struct error_info{
149 unsigned char code1, code2;
150 unsigned short int devices;
151 char * text;
152 };
153
154 struct error_info2{
155 unsigned char code1, code2_min, code2_max;
156 unsigned short int devices;
157 char * text;
158 };
159
160 static struct error_info2 additional2[] =
161 {
162 {0x40,0x00,0x7f,D,"Ram failure (%x)"},
163 {0x40,0x80,0xff,D|T|L|P|W|R|S|O|M|C,"Diagnostic failure on component (%x)"},
164 {0x41,0x00,0xff,D,"Data path failure (%x)"},
165 {0x42,0x00,0xff,D,"Power-on or self-test failure (%x)"},
166 {0, 0, 0, 0, NULL}
167 };
168
169 static struct error_info additional[] =
170 {
171 {0x00,0x01,T,"Filemark detected"},
172 {0x00,0x02,T|S,"End-of-partition/medium detected"},
173 {0x00,0x03,T,"Setmark detected"},
174 {0x00,0x04,T|S,"Beginning-of-partition/medium detected"},
175 {0x00,0x05,T|S,"End-of-data detected"},
176 {0x00,0x06,D|T|L|P|W|R|S|O|M|C,"I/O process terminated"},
177 {0x00,0x11,R,"Audio play operation in progress"},
178 {0x00,0x12,R,"Audio play operation paused"},
179 {0x00,0x13,R,"Audio play operation successfully completed"},
180 {0x00,0x14,R,"Audio play operation stopped due to error"},
181 {0x00,0x15,R,"No current audio status to return"},
182 {0x01,0x00,D|W|O,"No index/sector signal"},
183 {0x02,0x00,D|W|R|O|M,"No seek complete"},
184 {0x03,0x00,D|T|L|W|S|O,"Peripheral device write fault"},
185 {0x03,0x01,T,"No write current"},
186 {0x03,0x02,T,"Excessive write errors"},
187 {0x04,0x00,D|T|L|P|W|R|S|O|M|C,
188 "Logical unit not ready, cause not reportable"},
189 {0x04,0x01,D|T|L|P|W|R|S|O|M|C,
190 "Logical unit is in process of becoming ready"},
191 {0x04,0x02,D|T|L|P|W|R|S|O|M|C,
192 "Logical unit not ready, initializing command required"},
193 {0x04,0x03,D|T|L|P|W|R|S|O|M|C,
194 "Logical unit not ready, manual intervention required"},
195 {0x04,0x04,D|T|L|O,"Logical unit not ready, format in progress"},
196 {0x05,0x00,D|T|L|W|R|S|O|M|C,"Logical unit does not respond to selection"},
197 {0x06,0x00,D|W|R|O|M,"No reference position found"},
198 {0x07,0x00,D|T|L|W|R|S|O|M,"Multiple peripheral devices selected"},
199 {0x08,0x00,D|T|L|W|R|S|O|M|C,"Logical unit communication failure"},
200 {0x08,0x01,D|T|L|W|R|S|O|M|C,"Logical unit communication time-out"},
201 {0x08,0x02,D|T|L|W|R|S|O|M|C,"Logical unit communication parity error"},
202 {0x09,0x00,D|T|W|R|O,"Track following error"},
203 {0x09,0x01,W|R|O,"Tracking servo failure"},
204 {0x09,0x02,W|R|O,"Focus servo failure"},
205 {0x09,0x03,W|R|O,"Spindle servo failure"},
206 {0x0A,0x00,D|T|L|P|W|R|S|O|M|C,"Error log overflow"},
207 {0x0C,0x00,T|S,"Write error"},
208 {0x0C,0x01,D|W|O,"Write error recovered with auto reallocation"},
209 {0x0C,0x02,D|W|O,"Write error - auto reallocation failed"},
210 {0x10,0x00,D|W|O,"Id crc or ecc error"},
211 {0x11,0x00,D|T|W|R|S|O,"Unrecovered read error"},
212 {0x11,0x01,D|T|W|S|O,"Read retries exhausted"},
213 {0x11,0x02,D|T|W|S|O,"Error too long to correct"},
214 {0x11,0x03,D|T|W|S|O,"Multiple read errors"},
215 {0x11,0x04,D|W|O,"Unrecovered read error - auto reallocate failed"},
216 {0x11,0x05,W|R|O,"L-ec uncorrectable error"},
217 {0x11,0x06,W|R|O,"Circ unrecovered error"},
218 {0x11,0x07,W|O,"Data resychronization error"},
219 {0x11,0x08,T,"Incomplete block read"},
220 {0x11,0x09,T,"No gap found"},
221 {0x11,0x0A,D|T|O,"Miscorrected error"},
222 {0x11,0x0B,D|W|O,"Unrecovered read error - recommend reassignment"},
223 {0x11,0x0C,D|W|O,"Unrecovered read error - recommend rewrite the data"},
224 {0x12,0x00,D|W|O,"Address mark not found for id field"},
225 {0x13,0x00,D|W|O,"Address mark not found for data field"},
226 {0x14,0x00,D|T|L|W|R|S|O,"Recorded entity not found"},
227 {0x14,0x01,D|T|W|R|O,"Record not found"},
228 {0x14,0x02,T,"Filemark or setmark not found"},
229 {0x14,0x03,T,"End-of-data not found"},
230 {0x14,0x04,T,"Block sequence error"},
231 {0x15,0x00,D|T|L|W|R|S|O|M,"Random positioning error"},
232 {0x15,0x01,D|T|L|W|R|S|O|M,"Mechanical positioning error"},
233 {0x15,0x02,D|T|W|R|O,"Positioning error detected by read of medium"},
234 {0x16,0x00,D|W|O,"Data synchronization mark error"},
235 {0x17,0x00,D|T|W|R|S|O,"Recovered data with no error correction applied"},
236 {0x17,0x01,D|T|W|R|S|O,"Recovered data with retries"},
237 {0x17,0x02,D|T|W|R|O,"Recovered data with positive head offset"},
238 {0x17,0x03,D|T|W|R|O,"Recovered data with negative head offset"},
239 {0x17,0x04,W|R|O,"Recovered data with retries and/or circ applied"},
240 {0x17,0x05,D|W|R|O,"Recovered data using previous sector id"},
241 {0x17,0x06,D|W|O,"Recovered data without ecc - data auto-reallocated"},
242 {0x17,0x07,D|W|O,"Recovered data without ecc - recommend reassignment"},
243 {0x18,0x00,D|T|W|R|O,"Recovered data with error correction applied"},
244 {0x18,0x01,D|W|R|O,"Recovered data with error correction and retries applied"},
245 {0x18,0x02,D|W|R|O,"Recovered data - data auto-reallocated"},
246 {0x18,0x03,R,"Recovered data with circ"},
247 {0x18,0x04,R,"Recovered data with lec"},
248 {0x18,0x05,D|W|R|O,"Recovered data - recommend reassignment"},
249 {0x19,0x00,D|O,"Defect list error"},
250 {0x19,0x01,D|O,"Defect list not available"},
251 {0x19,0x02,D|O,"Defect list error in primary list"},
252 {0x19,0x03,D|O,"Defect list error in grown list"},
253 {0x1A,0x00,D|T|L|P|W|R|S|O|M|C,"Parameter list length error"},
254 {0x1B,0x00,D|T|L|P|W|R|S|O|M|C,"Synchronous data transfer error"},
255 {0x1C,0x00,D|O,"Defect list not found"},
256 {0x1C,0x01,D|O,"Primary defect list not found"},
257 {0x1C,0x02,D|O,"Grown defect list not found"},
258 {0x1D,0x00,D|W|O,"Miscompare during verify operation"},
259 {0x1E,0x00,D|W|O,"Recovered id with ecc correction"},
260 {0x20,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid command operation code"},
261 {0x21,0x00,D|T|W|R|O|M,"Logical block address out of range"},
262 {0x21,0x01,M,"Invalid element address"},
263 {0x22,0x00,D,"Illegal function (should use 20 00, 24 00, or 26 00)"},
264 {0x24,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid field in cdb"},
265 {0x25,0x00,D|T|L|P|W|R|S|O|M|C,"Logical unit not supported"},
266 {0x26,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid field in parameter list"},
267 {0x26,0x01,D|T|L|P|W|R|S|O|M|C,"Parameter not supported"},
268 {0x26,0x02,D|T|L|P|W|R|S|O|M|C,"Parameter value invalid"},
269 {0x26,0x03,D|T|L|P|W|R|S|O|M|C,"Threshold parameters not supported"},
270 {0x27,0x00,D|T|W|O,"Write protected"},
271 {0x28,0x00,D|T|L|P|W|R|S|O|M|C,"Not ready to ready transition (medium may have changed)"},
272 {0x28,0x01,M,"Import or export element accessed"},
273 {0x29,0x00,D|T|L|P|W|R|S|O|M|C,"Power on, reset, or bus device reset occurred"},
274 {0x2A,0x00,D|T|L|W|R|S|O|M|C,"Parameters changed"},
275 {0x2A,0x01,D|T|L|W|R|S|O|M|C,"Mode parameters changed"},
276 {0x2A,0x02,D|T|L|W|R|S|O|M|C,"Log parameters changed"},
277 {0x2B,0x00,D|T|L|P|W|R|S|O|C,"Copy cannot execute since host cannot disconnect"},
278 {0x2C,0x00,D|T|L|P|W|R|S|O|M|C,"Command sequence error"},
279 {0x2C,0x01,S,"Too many windows specified"},
280 {0x2C,0x02,S,"Invalid combination of windows specified"},
281 {0x2D,0x00,T,"Overwrite error on update in place"},
282 {0x2F,0x00,D|T|L|P|W|R|S|O|M|C,"Commands cleared by another initiator"},
283 {0x30,0x00,D|T|W|R|O|M,"Incompatible medium installed"},
284 {0x30,0x01,D|T|W|R|O,"Cannot read medium - unknown format"},
285 {0x30,0x02,D|T|W|R|O,"Cannot read medium - incompatible format"},
286 {0x30,0x03,D|T,"Cleaning cartridge installed"},
287 {0x31,0x00,D|T|W|O,"Medium format corrupted"},
288 {0x31,0x01,D|L|O,"Format command failed"},
289 {0x32,0x00,D|W|O,"No defect spare location available"},
290 {0x32,0x01,D|W|O,"Defect list update failure"},
291 {0x33,0x00,T,"Tape length error"},
292 {0x36,0x00,L,"Ribbon, ink, or toner failure"},
293 {0x37,0x00,D|T|L|W|R|S|O|M|C,"Rounded parameter"},
294 {0x39,0x00,D|T|L|W|R|S|O|M|C,"Saving parameters not supported"},
295 {0x3A,0x00,D|T|L|W|R|S|O|M,"Medium not present"},
296 {0x3B,0x00,T|L,"Sequential positioning error"},
297 {0x3B,0x01,T,"Tape position error at beginning-of-medium"},
298 {0x3B,0x02,T,"Tape position error at end-of-medium"},
299 {0x3B,0x03,L,"Tape or electronic vertical forms unit not ready"},
300 {0x3B,0x04,L,"Slew failure"},
301 {0x3B,0x05,L,"Paper jam"},
302 {0x3B,0x06,L,"Failed to sense top-of-form"},
303 {0x3B,0x07,L,"Failed to sense bottom-of-form"},
304 {0x3B,0x08,T,"Reposition error"},
305 {0x3B,0x09,S,"Read past end of medium"},
306 {0x3B,0x0A,S,"Read past beginning of medium"},
307 {0x3B,0x0B,S,"Position past end of medium"},
308 {0x3B,0x0C,S,"Position past beginning of medium"},
309 {0x3B,0x0D,M,"Medium destination element full"},
310 {0x3B,0x0E,M,"Medium source element empty"},
311 {0x3D,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid bits in identify message"},
312 {0x3E,0x00,D|T|L|P|W|R|S|O|M|C,"Logical unit has not self-configured yet"},
313 {0x3F,0x00,D|T|L|P|W|R|S|O|M|C,"Target operating conditions have changed"},
314 {0x3F,0x01,D|T|L|P|W|R|S|O|M|C,"Microcode has been changed"},
315 {0x3F,0x02,D|T|L|P|W|R|S|O|M|C,"Changed operating definition"},
316 {0x3F,0x03,D|T|L|P|W|R|S|O|M|C,"Inquiry data has changed"},
317 {0x43,0x00,D|T|L|P|W|R|S|O|M|C,"Message error"},
318 {0x44,0x00,D|T|L|P|W|R|S|O|M|C,"Internal target failure"},
319 {0x45,0x00,D|T|L|P|W|R|S|O|M|C,"Select or reselect failure"},
320 {0x46,0x00,D|T|L|P|W|R|S|O|M|C,"Unsuccessful soft reset"},
321 {0x47,0x00,D|T|L|P|W|R|S|O|M|C,"Scsi parity error"},
322 {0x48,0x00,D|T|L|P|W|R|S|O|M|C,"Initiator detected error message received"},
323 {0x49,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid message error"},
324 {0x4A,0x00,D|T|L|P|W|R|S|O|M|C,"Command phase error"},
325 {0x4B,0x00,D|T|L|P|W|R|S|O|M|C,"Data phase error"},
326 {0x4C,0x00,D|T|L|P|W|R|S|O|M|C,"Logical unit failed self-configuration"},
327 {0x4E,0x00,D|T|L|P|W|R|S|O|M|C,"Overlapped commands attempted"},
328 {0x50,0x00,T,"Write append error"},
329 {0x50,0x01,T,"Write append position error"},
330 {0x50,0x02,T,"Position error related to timing"},
331 {0x51,0x00,T|O,"Erase failure"},
332 {0x52,0x00,T,"Cartridge fault"},
333 {0x53,0x00,D|T|L|W|R|S|O|M,"Media load or eject failed"},
334 {0x53,0x01,T,"Unload tape failure"},
335 {0x53,0x02,D|T|W|R|O|M,"Medium removal prevented"},
336 {0x54,0x00,P,"Scsi to host system interface failure"},
337 {0x55,0x00,P,"System resource failure"},
338 {0x57,0x00,R,"Unable to recover table-of-contents"},
339 {0x58,0x00,O,"Generation does not exist"},
340 {0x59,0x00,O,"Updated block read"},
341 {0x5A,0x00,D|T|L|P|W|R|S|O|M,"Operator request or state change input (unspecified)"},
342 {0x5A,0x01,D|T|W|R|O|M,"Operator medium removal request"},
343 {0x5A,0x02,D|T|W|O,"Operator selected write protect"},
344 {0x5A,0x03,D|T|W|O,"Operator selected write permit"},
345 {0x5B,0x00,D|T|L|P|W|R|S|O|M,"Log exception"},
346 {0x5B,0x01,D|T|L|P|W|R|S|O|M,"Threshold condition met"},
347 {0x5B,0x02,D|T|L|P|W|R|S|O|M,"Log counter at maximum"},
348 {0x5B,0x03,D|T|L|P|W|R|S|O|M,"Log list codes exhausted"},
349 {0x5C,0x00,D|O,"Rpl status change"},
350 {0x5C,0x01,D|O,"Spindles synchronized"},
351 {0x5C,0x02,D|O,"Spindles not synchronized"},
352 {0x60,0x00,S,"Lamp failure"},
353 {0x61,0x00,S,"Video acquisition error"},
354 {0x61,0x01,S,"Unable to acquire video"},
355 {0x61,0x02,S,"Out of focus"},
356 {0x62,0x00,S,"Scan head positioning error"},
357 {0x63,0x00,R,"End of user area encountered on this track"},
358 {0x64,0x00,R,"Illegal mode for this track"},
359 {0, 0, 0, NULL}
360 };
361 #endif
362
363 #if (CONSTANTS & CONST_SENSE)
364 static char *snstext[] = {
365 "None","Recovered Error","Not Ready","Medium Error","Hardware Error",
366 "Illegal Request","Unit Attention","Data Protect","Blank Check",
367 "Key=E","Key=F","Filemark","End-Of-Medium","Incorrect Block Length",
368 "14","15"};
369 #endif
370
371
372
373 void print_sense(char * devclass, Scsi_Cmnd * SCpnt)
374 {
375 int i, s;
376 int sense_class, valid, code;
377 unsigned char * sense_buffer = SCpnt->sense_buffer;
378 char * error = NULL;
379 int dev = SCpnt->request.dev;
380
381 sense_class = (sense_buffer[0] >> 4) & 0x07;
382 code = sense_buffer[0] & 0xf;
383 valid = sense_buffer[0] & 0x80;
384
385 if (sense_class == 7) {
386 s = sense_buffer[7] + 8;
387 if(s > sizeof(SCpnt->sense_buffer)) s = sizeof(SCpnt->sense_buffer);
388
389 if (!valid)
390 printk("extra data not valid ");
391
392 if (sense_buffer[2] & 0x80) printk( "FMK ");
393 if (sense_buffer[2] & 0x40) printk( "EOM ");
394 if (sense_buffer[2] & 0x20) printk( "ILI ");
395
396 switch (code) {
397 case 0x0:
398 error = "Current";
399 break;
400 case 0x1:
401 error = "Deferred";
402 break;
403 default:
404 error = "Invalid";
405 }
406
407 printk("%s error ", error);
408
409 #if (CONSTANTS & CONST_SENSE)
410 if (sense_buffer[2] & 0x80) printk( "FMK ");
411 if (sense_buffer[2] & 0x40) printk( "EOM ");
412 if (sense_buffer[2] & 0x20) printk( "ILI ");
413 printk( "%s%x: sense key %s\n", devclass, dev, snstext[sense_buffer[2] & 0x0f]);
414 #else
415 printk("%s%x: sns = %2x %2x\n", devclass, dev, sense_buffer[0], sense_buffer[2]);
416 #endif
417
418
419 if(sense_buffer[7] + 7 < 13 ||
420 (sense_buffer[12] == 0 && sense_buffer[13] == 0)) goto done;
421
422 #if (CONSTANTS & CONST_XSENSE)
423 for(i=0; additional[i].text; i++)
424 if(additional[i].code1 == sense_buffer[12] &&
425 additional[i].code2 == sense_buffer[13])
426 printk("Additional sense indicates %s\n", additional[i].text);
427
428 for(i=0; additional2[i].text; i++)
429 if(additional2[i].code1 == sense_buffer[12] &&
430 additional2[i].code2_min >= sense_buffer[13] &&
431 additional2[i].code2_max <= sense_buffer[13]) {
432 printk("Additional sense indicates ");
433 printk(additional2[i].text, sense_buffer[13]);
434 printk("\n");
435 };
436 #else
437 printk("ASC=%2x ASCQ=%2x\n", sense_buffer[12], sense_buffer[13]);
438 #endif
439 } else {
440
441 #if (CONSTANTS & CONST_SENSE)
442 if (sense_buffer[0] < 15)
443 printk("%s%x: old sense key %s\n", devclass, dev, snstext[sense_buffer[0] & 0x0f]);
444 else
445 #endif
446 printk("%s%x: sns = %2x %2x\n", devclass, dev, sense_buffer[0], sense_buffer[2]);
447
448 printk("Non-extended sense class %d code 0x%0x ", sense_class, code);
449 s = 4;
450 }
451
452 done:
453 for (i = 0; i < s; ++i)
454 printk("0x%02x ", sense_buffer[i]);
455
456 return;
457 }
458
459
460 #endif CONFIG_SCSI