taglinefilesource code
L150drivers/scsi/constants.c{0x40,0x80,0xff,D|T|L|P|W|R|S|O|M|C,"Diagnostic failure on component (%x)"},
L163drivers/scsi/constants.c{0x00,0x06,D|T|L|P|W|R|S|O|M|C,"I/O process terminated"},
L171drivers/scsi/constants.c{0x03,0x00,D|T|L|W|S|O,"Peripheral device write fault"},
L174drivers/scsi/constants.c{0x04,0x00,D|T|L|P|W|R|S|O|M|C,
L176drivers/scsi/constants.c{0x04,0x01,D|T|L|P|W|R|S|O|M|C,
L178drivers/scsi/constants.c{0x04,0x02,D|T|L|P|W|R|S|O|M|C,
L180drivers/scsi/constants.c{0x04,0x03,D|T|L|P|W|R|S|O|M|C,
L182drivers/scsi/constants.c{0x04,0x04,D|T|L|O,"Logical unit not ready, format in progress"},
L183drivers/scsi/constants.c{0x05,0x00,D|T|L|W|R|S|O|M|C,"Logical unit does not respond to selection"},
L185drivers/scsi/constants.c{0x07,0x00,D|T|L|W|R|S|O|M,"Multiple peripheral devices selected"},
L186drivers/scsi/constants.c{0x08,0x00,D|T|L|W|R|S|O|M|C,"Logical unit communication failure"},
L187drivers/scsi/constants.c{0x08,0x01,D|T|L|W|R|S|O|M|C,"Logical unit communication time-out"},
L188drivers/scsi/constants.c{0x08,0x02,D|T|L|W|R|S|O|M|C,"Logical unit communication parity error"},
L193drivers/scsi/constants.c{0x0A,0x00,D|T|L|P|W|R|S|O|M|C,"Error log overflow"},
L213drivers/scsi/constants.c{0x14,0x00,D|T|L|W|R|S|O,"Recorded entity not found"},
L218drivers/scsi/constants.c{0x15,0x00,D|T|L|W|R|S|O|M,"Random positioning error"},
L219drivers/scsi/constants.c{0x15,0x01,D|T|L|W|R|S|O|M,"Mechanical positioning error"},
L240drivers/scsi/constants.c{0x1A,0x00,D|T|L|P|W|R|S|O|M|C,"Parameter list length error"},
L241drivers/scsi/constants.c{0x1B,0x00,D|T|L|P|W|R|S|O|M|C,"Synchronous data transfer error"},
L247drivers/scsi/constants.c{0x20,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid command operation code"},
L251drivers/scsi/constants.c{0x24,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid field in cdb"},
L252drivers/scsi/constants.c{0x25,0x00,D|T|L|P|W|R|S|O|M|C,"Logical unit not supported"},
L253drivers/scsi/constants.c{0x26,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid field in parameter list"},
L254drivers/scsi/constants.c{0x26,0x01,D|T|L|P|W|R|S|O|M|C,"Parameter not supported"},
L255drivers/scsi/constants.c{0x26,0x02,D|T|L|P|W|R|S|O|M|C,"Parameter value invalid"},
L256drivers/scsi/constants.c{0x26,0x03,D|T|L|P|W|R|S|O|M|C,"Threshold parameters not supported"},
L258drivers/scsi/constants.c{0x28,0x00,D|T|L|P|W|R|S|O|M|C,"Not ready to ready transition (medium may have changed)"},
L260drivers/scsi/constants.c{0x29,0x00,D|T|L|P|W|R|S|O|M|C,"Power on, reset, or bus device reset occurred"},
L261drivers/scsi/constants.c{0x2A,0x00,D|T|L|W|R|S|O|M|C,"Parameters changed"},
L262drivers/scsi/constants.c{0x2A,0x01,D|T|L|W|R|S|O|M|C,"Mode parameters changed"},
L263drivers/scsi/constants.c{0x2A,0x02,D|T|L|W|R|S|O|M|C,"Log parameters changed"},
L264drivers/scsi/constants.c{0x2B,0x00,D|T|L|P|W|R|S|O|C,"Copy cannot execute since host cannot disconnect"},
L265drivers/scsi/constants.c{0x2C,0x00,D|T|L|P|W|R|S|O|M|C,"Command sequence error"},
L269drivers/scsi/constants.c{0x2F,0x00,D|T|L|P|W|R|S|O|M|C,"Commands cleared by another initiator"},
L275drivers/scsi/constants.c{0x31,0x01,D|L|O,"Format command failed"},
L279drivers/scsi/constants.c{0x36,0x00,L,"Ribbon, ink, or toner failure"},
L280drivers/scsi/constants.c{0x37,0x00,D|T|L|W|R|S|O|M|C,"Rounded parameter"},
L281drivers/scsi/constants.c{0x39,0x00,D|T|L|W|R|S|O|M|C,"Saving parameters not supported"},
L282drivers/scsi/constants.c{0x3A,0x00,D|T|L|W|R|S|O|M,"Medium not present"},
L283drivers/scsi/constants.c{0x3B,0x00,T|L,"Sequential positioning error"},
L286drivers/scsi/constants.c{0x3B,0x03,L,"Tape or electronic vertical forms unit not ready"},
L287drivers/scsi/constants.c{0x3B,0x04,L,"Slew failure"},
L288drivers/scsi/constants.c{0x3B,0x05,L,"Paper jam"},
L289drivers/scsi/constants.c{0x3B,0x06,L,"Failed to sense top-of-form"},
L290drivers/scsi/constants.c{0x3B,0x07,L,"Failed to sense bottom-of-form"},
L298drivers/scsi/constants.c{0x3D,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid bits in identify message"},
L299drivers/scsi/constants.c{0x3E,0x00,D|T|L|P|W|R|S|O|M|C,"Logical unit has not self-configured yet"},
L300drivers/scsi/constants.c{0x3F,0x00,D|T|L|P|W|R|S|O|M|C,"Target operating conditions have changed"},
L301drivers/scsi/constants.c{0x3F,0x01,D|T|L|P|W|R|S|O|M|C,"Microcode has been changed"},
L302drivers/scsi/constants.c{0x3F,0x02,D|T|L|P|W|R|S|O|M|C,"Changed operating definition"},
L303drivers/scsi/constants.c{0x3F,0x03,D|T|L|P|W|R|S|O|M|C,"Inquiry data has changed"},
L304drivers/scsi/constants.c{0x43,0x00,D|T|L|P|W|R|S|O|M|C,"Message error"},
L305drivers/scsi/constants.c{0x44,0x00,D|T|L|P|W|R|S|O|M|C,"Internal target failure"},
L306drivers/scsi/constants.c{0x45,0x00,D|T|L|P|W|R|S|O|M|C,"Select or reselect failure"},
L307drivers/scsi/constants.c{0x46,0x00,D|T|L|P|W|R|S|O|M|C,"Unsuccessful soft reset"},
L308drivers/scsi/constants.c{0x47,0x00,D|T|L|P|W|R|S|O|M|C,"Scsi parity error"},
L309drivers/scsi/constants.c{0x48,0x00,D|T|L|P|W|R|S|O|M|C,"Initiator detected error message received"},
L310drivers/scsi/constants.c{0x49,0x00,D|T|L|P|W|R|S|O|M|C,"Invalid message error"},
L311drivers/scsi/constants.c{0x4A,0x00,D|T|L|P|W|R|S|O|M|C,"Command phase error"},
L312drivers/scsi/constants.c{0x4B,0x00,D|T|L|P|W|R|S|O|M|C,"Data phase error"},
L313drivers/scsi/constants.c{0x4C,0x00,D|T|L|P|W|R|S|O|M|C,"Logical unit failed self-configuration"},
L314drivers/scsi/constants.c{0x4E,0x00,D|T|L|P|W|R|S|O|M|C,"Overlapped commands attempted"},
L320drivers/scsi/constants.c{0x53,0x00,D|T|L|W|R|S|O|M,"Media load or eject failed"},
L328drivers/scsi/constants.c{0x5A,0x00,D|T|L|P|W|R|S|O|M,"Operator request or state change input (unspecified)"},
L332drivers/scsi/constants.c{0x5B,0x00,D|T|L|P|W|R|S|O|M,"Log exception"},
L333drivers/scsi/constants.c{0x5B,0x01,D|T|L|P|W|R|S|O|M,"Threshold condition met"},
L334drivers/scsi/constants.c{0x5B,0x02,D|T|L|P|W|R|S|O|M,"Log counter at maximum"},
L335drivers/scsi/constants.c{0x5B,0x03,D|T|L|P|W|R|S|O|M,"Log list codes exhausted"},