root/drivers/net/z8530.h

/* [previous][next][first][last][top][bottom][index][help] */

INCLUDED FROM


   1 
   2 /* 8530 Serial Communications Controller Register definitions */
   3 #define FLAG    0x7e
   4 
   5 /* Write Register 0 */
   6 #define R0      0               /* Register selects */
   7 #define R1      1
   8 #define R2      2
   9 #define R3      3
  10 #define R4      4
  11 #define R5      5
  12 #define R6      6
  13 #define R7      7
  14 #define R8      8
  15 #define R9      9
  16 #define R10     10
  17 #define R11     11
  18 #define R12     12
  19 #define R13     13
  20 #define R14     14
  21 #define R15     15
  22 
  23 #define NULLCODE        0       /* Null Code */
  24 #define POINT_HIGH      0x8     /* Select upper half of registers */
  25 #define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */
  26 #define SEND_ABORT      0x18    /* HDLC Abort */
  27 #define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
  28 #define RES_Tx_P        0x28    /* Reset TxINT Pending */
  29 #define ERR_RES         0x30    /* Error Reset */
  30 #define RES_H_IUS       0x38    /* Reset highest IUS */
  31 
  32 #define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */
  33 #define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */
  34 #define RES_EOM_L       0xC0    /* Reset EOM latch */
  35 
  36 /* Write Register 1 */
  37 
  38 #define EXT_INT_ENAB    0x1     /* Ext Int Enable */
  39 #define TxINT_ENAB      0x2     /* Tx Int Enable */
  40 #define PAR_SPEC        0x4     /* Parity is special condition */
  41 
  42 #define RxINT_DISAB     0       /* Rx Int Disable */
  43 #define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */
  44 #define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */
  45 #define INT_ERR_Rx      0x18    /* Int on error only */
  46 
  47 #define WT_RDY_RT       0x20    /* Wait/Ready on R/T */
  48 #define WT_FN_RDYFN     0x40    /* Wait/FN/Ready FN */
  49 #define WT_RDY_ENAB     0x80    /* Wait/Ready Enable */
  50 
  51 /* Write Register #2 (Interrupt Vector) */
  52 
  53 /* Write Register 3 */
  54 
  55 #define RxENABLE        0x1     /* Rx Enable */
  56 #define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */
  57 #define ADD_SM          0x4     /* Address Search Mode (SDLC) */
  58 #define RxCRC_ENAB      0x8     /* Rx CRC Enable */
  59 #define ENT_HM          0x10    /* Enter Hunt Mode */
  60 #define AUTO_ENAB       0x20    /* Auto Enables */
  61 #define Rx5             0x0     /* Rx 5 Bits/Character */
  62 #define Rx7             0x40    /* Rx 7 Bits/Character */
  63 #define Rx6             0x80    /* Rx 6 Bits/Character */
  64 #define Rx8             0xc0    /* Rx 8 Bits/Character */
  65 
  66 /* Write Register 4 */
  67 
  68 #define PAR_ENA         0x1     /* Parity Enable */
  69 #define PAR_EVEN        0x2     /* Parity Even/Odd* */
  70 
  71 #define SYNC_ENAB       0       /* Sync Modes Enable */
  72 #define SB1             0x4     /* 1 stop bit/char */
  73 #define SB15            0x8     /* 1.5 stop bits/char */
  74 #define SB2             0xc     /* 2 stop bits/char */
  75 
  76 #define MONSYNC         0       /* 8 Bit Sync character */
  77 #define BISYNC          0x10    /* 16 bit sync character */
  78 #define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */
  79 #define EXTSYNC         0x30    /* External Sync Mode */
  80 
  81 #define X1CLK           0x0     /* x1 clock mode */
  82 #define X16CLK          0x40    /* x16 clock mode */
  83 #define X32CLK          0x80    /* x32 clock mode */
  84 #define X64CLK          0xC0    /* x64 clock mode */
  85 
  86 /* Write Register 5 */
  87 
  88 #define TxCRC_ENAB      0x1     /* Tx CRC Enable */
  89 #define RTS             0x2     /* RTS */
  90 #define SDLC_CRC        0x4     /* SDLC/CRC-16 */
  91 #define TxENAB          0x8     /* Tx Enable */
  92 #define SND_BRK         0x10    /* Send Break */
  93 #define Tx5             0x0     /* Tx 5 bits (or less)/character */
  94 #define Tx7             0x20    /* Tx 7 bits/character */
  95 #define Tx6             0x40    /* Tx 6 bits/character */
  96 #define Tx8             0x60    /* Tx 8 bits/character */
  97 #define DTR             0x80    /* DTR */
  98 
  99 /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
 100 
 101 /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
 102 
 103 /* Write Register 8 (transmit buffer) */
 104 
 105 /* Write Register 9 (Master interrupt control) */
 106 #define VIS     1       /* Vector Includes Status */
 107 #define NV      2       /* No Vector */
 108 #define DLC     4       /* Disable Lower Chain */
 109 #define MIE     8       /* Master Interrupt Enable */
 110 #define STATHI  0x10    /* Status high */
 111 #define NORESET 0       /* No reset on write to R9 */
 112 #define CHRB    0x40    /* Reset channel B */
 113 #define CHRA    0x80    /* Reset channel A */
 114 #define FHWRES  0xc0    /* Force hardware reset */
 115 
 116 /* Write Register 10 (misc control bits) */
 117 #define BIT6    1       /* 6 bit/8bit sync */
 118 #define LOOPMODE 2      /* SDLC Loop mode */
 119 #define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */
 120 #define MARKIDLE 8      /* Mark/flag on idle */
 121 #define GAOP    0x10    /* Go active on poll */
 122 #define NRZ     0       /* NRZ mode */
 123 #define NRZI    0x20    /* NRZI mode */
 124 #define FM1     0x40    /* FM1 (transition = 1) */
 125 #define FM0     0x60    /* FM0 (transition = 0) */
 126 #define CRCPS   0x80    /* CRC Preset I/O */
 127 
 128 /* Write Register 11 (Clock Mode control) */
 129 #define TRxCXT  0       /* TRxC = Xtal output */
 130 #define TRxCTC  1       /* TRxC = Transmit clock */
 131 #define TRxCBR  2       /* TRxC = BR Generator Output */
 132 #define TRxCDP  3       /* TRxC = DPLL output */
 133 #define TRxCOI  4       /* TRxC O/I */
 134 #define TCRTxCP 0       /* Transmit clock = RTxC pin */
 135 #define TCTRxCP 8       /* Transmit clock = TRxC pin */
 136 #define TCBR    0x10    /* Transmit clock = BR Generator output */
 137 #define TCDPLL  0x18    /* Transmit clock = DPLL output */
 138 #define RCRTxCP 0       /* Receive clock = RTxC pin */
 139 #define RCTRxCP 0x20    /* Receive clock = TRxC pin */
 140 #define RCBR    0x40    /* Receive clock = BR Generator output */
 141 #define RCDPLL  0x60    /* Receive clock = DPLL output */
 142 #define RTxCX   0x80    /* RTxC Xtal/No Xtal */
 143 
 144 /* Write Register 12 (lower byte of baud rate generator time constant) */
 145 
 146 /* Write Register 13 (upper byte of baud rate generator time constant) */
 147 
 148 /* Write Register 14 (Misc control bits) */
 149 #define BRENABL 1       /* Baud rate generator enable */
 150 #define BRSRC   2       /* Baud rate generator source */
 151 #define DTRREQ  4       /* DTR/Request function */
 152 #define AUTOECHO 8      /* Auto Echo */
 153 #define LOOPBAK 0x10    /* Local loopback */
 154 #define SEARCH  0x20    /* Enter search mode */
 155 #define RMC     0x40    /* Reset missing clock */
 156 #define DISDPLL 0x60    /* Disable DPLL */
 157 #define SSBR    0x80    /* Set DPLL source = BR generator */
 158 #define SSRTxC  0xa0    /* Set DPLL source = RTxC */
 159 #define SFMM    0xc0    /* Set FM mode */
 160 #define SNRZI   0xe0    /* Set NRZI mode */
 161 
 162 /* Write Register 15 (external/status interrupt control) */
 163 #define ZCIE    2       /* Zero count IE */
 164 #define DCDIE   8       /* DCD IE */
 165 #define SYNCIE  0x10    /* Sync/hunt IE */
 166 #define CTSIE   0x20    /* CTS IE */
 167 #define TxUIE   0x40    /* Tx Underrun/EOM IE */
 168 #define BRKIE   0x80    /* Break/Abort IE */
 169 
 170 
 171 /* Read Register 0 */
 172 #define Rx_CH_AV        0x1     /* Rx Character Available */
 173 #define ZCOUNT          0x2     /* Zero count */
 174 #define Tx_BUF_EMP      0x4     /* Tx Buffer empty */
 175 #define DCD             0x8     /* DCD */
 176 #define SYNC_HUNT       0x10    /* Sync/hunt */
 177 #define CTS             0x20    /* CTS */
 178 #define TxEOM           0x40    /* Tx underrun */
 179 #define BRK_ABRT        0x80    /* Break/Abort */
 180 
 181 /* Read Register 1 */
 182 #define ALL_SNT         0x1     /* All sent */
 183 /* Residue Data for 8 Rx bits/char programmed */
 184 #define RES3            0x8     /* 0/3 */
 185 #define RES4            0x4     /* 0/4 */
 186 #define RES5            0xc     /* 0/5 */
 187 #define RES6            0x2     /* 0/6 */
 188 #define RES7            0xa     /* 0/7 */
 189 #define RES8            0x6     /* 0/8 */
 190 #define RES18           0xe     /* 1/8 */
 191 #define RES28           0x0     /* 2/8 */
 192 /* Special Rx Condition Interrupts */
 193 #define PAR_ERR         0x10    /* Parity error */
 194 #define Rx_OVR          0x20    /* Rx Overrun Error */
 195 #define CRC_ERR         0x40    /* CRC/Framing Error */
 196 #define END_FR          0x80    /* End of Frame (SDLC) */
 197 
 198 /* Read Register 2 (channel b only) - Interrupt vector */
 199 
 200 /* Read Register 3 (interrupt pending register) ch a only */
 201 #define CHBEXT  0x1             /* Channel B Ext/Stat IP */
 202 #define CHBTxIP 0x2             /* Channel B Tx IP */
 203 #define CHBRxIP 0x4             /* Channel B Rx IP */
 204 #define CHAEXT  0x8             /* Channel A Ext/Stat IP */
 205 #define CHATxIP 0x10            /* Channel A Tx IP */
 206 #define CHARxIP 0x20            /* Channel A Rx IP */
 207 
 208 /* Read Register 8 (receive data register) */
 209 
 210 /* Read Register 10  (misc status bits) */
 211 #define ONLOOP  2               /* On loop */
 212 #define LOOPSEND 0x10           /* Loop sending */
 213 #define CLK2MIS 0x40            /* Two clocks missing */
 214 #define CLK1MIS 0x80            /* One clock missing */
 215 
 216 /* Read Register 12 (lower byte of baud rate generator constant) */
 217 
 218 /* Read Register 13 (upper byte of baud rate generator constant) */
 219 
 220 /* Read Register 15 (value of WR 15) */

/* [previous][next][first][last][top][bottom][index][help] */