root/include/linux/interrupt.h

/* [previous][next][first][last][top][bottom][index][help] */

INCLUDED FROM


DEFINITIONS

This source file includes following definitions.
  1. mark_bh
  2. disable_bh
  3. enable_bh
  4. start_bh_atomic
  5. end_bh_atomic

   1 /* interrupt.h */
   2 #ifndef _LINUX_INTERRUPT_H
   3 #define _LINUX_INTERRUPT_H
   4 
   5 #include <linux/linkage.h>
   6 #include <asm/bitops.h>
   7 
   8 struct bh_struct {
   9         void (*routine)(void *);
  10         void *data;
  11 };
  12 
  13 extern unsigned long bh_active;
  14 extern unsigned long bh_mask;
  15 extern struct bh_struct bh_base[32];
  16 
  17 asmlinkage void do_bottom_half(void);
  18 
  19 /* Who gets which entry in bh_base.  Things which will occur most often
  20    should come first - in which case NET should be up the top with SERIAL/TQUEUE! */
  21    
  22 enum {
  23         TIMER_BH = 0,
  24         CONSOLE_BH,
  25         TQUEUE_BH,
  26         SERIAL_BH,
  27         NET_BH,
  28         IMMEDIATE_BH,
  29         KEYBOARD_BH,
  30         CYCLADES_BH,
  31         CM206_BH
  32 };
  33 
  34 extern inline void mark_bh(int nr)
     /* [previous][next][first][last][top][bottom][index][help] */
  35 {
  36         set_bit(nr, &bh_active);
  37 }
  38 
  39 extern inline void disable_bh(int nr)
     /* [previous][next][first][last][top][bottom][index][help] */
  40 {
  41         clear_bit(nr, &bh_mask);
  42 }
  43 
  44 extern inline void enable_bh(int nr)
     /* [previous][next][first][last][top][bottom][index][help] */
  45 {
  46         set_bit(nr, &bh_mask);
  47 }
  48 
  49 extern inline void start_bh_atomic(void)
     /* [previous][next][first][last][top][bottom][index][help] */
  50 {
  51         intr_count++;
  52 }
  53 
  54 extern inline void end_bh_atomic(void)
     /* [previous][next][first][last][top][bottom][index][help] */
  55 {
  56         if (intr_count == 1 && (bh_active & bh_mask))
  57                 do_bottom_half();
  58         intr_count--;
  59 }
  60 
  61 /*
  62  * Autoprobing for irqs:
  63  *
  64  * probe_irq_on() and probe_irq_off() provide robust primitives
  65  * for accurate IRQ probing during kernel initialization.  They are
  66  * reasonably simple to use, are not "fooled" by spurious interrupts,
  67  * and, unlike other attempts at IRQ probing, they do not get hung on
  68  * stuck interrupts (such as unused PS2 mouse interfaces on ASUS boards).
  69  *
  70  * For reasonably foolproof probing, use them as follows:
  71  *
  72  * 1. clear and/or mask the device's internal interrupt.
  73  * 2. sti();
  74  * 3. irqs = probe_irq_on();      // "take over" all unassigned idle IRQs
  75  * 4. enable the device and cause it to trigger an interrupt.
  76  * 5. wait for the device to interrupt, using non-intrusive polling or a delay.
  77  * 6. irq = probe_irq_off(irqs);  // get IRQ number, 0=none, negative=multiple
  78  * 7. service the device to clear its pending interrupt.
  79  * 8. loop again if paranoia is required.
  80  *
  81  * probe_irq_on() returns a mask of snarfed irq's.
  82  *
  83  * probe_irq_off() takes the mask as a parameter,
  84  * and returns the irq number which occurred,
  85  * or zero if none occurred, or a negative irq number
  86  * if more than one irq occurred.
  87  */
  88 extern unsigned long probe_irq_on(void);        /* returns 0 on failure */
  89 extern int probe_irq_off(unsigned long);        /* returns 0 or negative on failure */
  90 
  91 #endif

/* [previous][next][first][last][top][bottom][index][help] */