root/include/asm-sparc/ecc.h

/* [previous][next][first][last][top][bottom][index][help] */

INCLUDED FROM


   1 /* $Id: ecc.h,v 1.2 1995/11/25 02:31:37 davem Exp $
   2  * ecc.h: Definitions and defines for the external cache/memory
   3  *        controller on the sun4m.
   4  *
   5  * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
   6  */
   7 
   8 #ifndef _SPARC_ECC_H
   9 #define _SPARC_ECC_H
  10 
  11 /* These registers are accessed through the SRMMU passthrough ASI 0x20 */
  12 #define ECC_ENABLE     0x00000000       /* ECC enable register */
  13 #define ECC_FSTATUS    0x00000008       /* ECC fault status register */
  14 #define ECC_FADDR      0x00000010       /* ECC fault address register */
  15 #define ECC_DIGNOSTIC  0x00000018       /* ECC diagnostics register */
  16 #define ECC_MBAENAB    0x00000020       /* MBus arbiter enable register */
  17 #define ECC_DMESG      0x00001000       /* Diagnostic message passing area */
  18 
  19 /* ECC MBus Arbiter Enable register:
  20  *
  21  * ----------------------------------------
  22  * |              |SBUS|MOD3|MOD2|MOD1|RSV|
  23  * ----------------------------------------
  24  *  31           5   4   3    2    1    0
  25  *
  26  * SBUS: Enable MBus Arbiter on the SBus 0=off 1=on
  27  * MOD3: Enable MBus Arbiter on MBus module 3  0=off 1=on
  28  * MOD2: Enable MBus Arbiter on MBus module 2  0=off 1=on
  29  * MOD1: Enable MBus Arbiter on MBus module 1  0=off 1=on
  30  */
  31 
  32 #define ECC_MBAE_SBUS     0x00000010
  33 #define ECC_MBAE_MOD3     0x00000008
  34 #define ECC_MBAE_MOD2     0x00000004
  35 #define ECC_MBAE_MOD1     0x00000002 
  36 
  37 /* ECC Fault Control Register layout:
  38  *
  39  * -----------------------------
  40  * |    RESV   | ECHECK | EINT |
  41  * -----------------------------
  42  *  31        2     1       0
  43  *
  44  * ECHECK:  Enable ECC checking.  0=off 1=on
  45  * EINT:  Enable Interrupts for correctable errors. 0=off 1=on
  46  */ 
  47 #define ECC_FCR_CHECK    0x00000002
  48 #define ECC_FCR_INTENAB  0x00000001
  49 
  50 /* ECC Fault Address Register Zero layout:
  51  *
  52  * -----------------------------------------------------
  53  * | MID | S | RSV |  VA   | BM |AT| C| SZ |TYP| PADDR |
  54  * -----------------------------------------------------
  55  *  31-28  27 26-22  21-14   13  12 11 10-8 7-4   3-0
  56  *
  57  * MID: ModuleID of the faulting processor. ie. who did it?
  58  * S: Supervisor/Privileged access? 0=no 1=yes
  59  * VA: Bits 19-12 of the virtual faulting address, these are the
  60  *     superset bits in the virtual cache and can be used for
  61  *     a flush operation if necessary.
  62  * BM: Boot mode? 0=no 1=yes  This is just like the SRMMU boot
  63  *     mode bit.
  64  * AT: Did this fault happen during an atomic instruction? 0=no
  65  *     1=yes.  This means either an 'ldstub' or 'swap' instruction
  66  *     was in progress (but not finished) when this fault happened.
  67  *     This indicated whether the bus was locked when the fault
  68  *     occurred.
  69  * C: Did the pte for this access indicate that it was cacheable?
  70  *    0=no 1=yes
  71  * SZ: The size of the transaction.
  72  * TYP: The transaction type.
  73  * PADDR: Bits 35-32 of the physical address for the fault.
  74  */
  75 #define ECC_FADDR0_MIDMASK   0xf0000000
  76 #define ECC_FADDR0_S         0x08000000
  77 #define ECC_FADDR0_VADDR     0x003fc000
  78 #define ECC_FADDR0_BMODE     0x00002000
  79 #define ECC_FADDR0_ATOMIC    0x00001000
  80 #define ECC_FADDR0_CACHE     0x00000800
  81 #define ECC_FADDR0_SIZE      0x00000700
  82 #define ECC_FADDR0_TYPE      0x000000f0
  83 #define ECC_FADDR0_PADDR     0x0000000f
  84 
  85 /* ECC Fault Address Register One layout:
  86  *
  87  * -------------------------------------
  88  * |          Physical Address 31-0    |
  89  * -------------------------------------
  90  *  31                               0
  91  *
  92  * You get the upper 4 bits of the physical address from the
  93  * PADDR field in ECC Fault Address Zero register.
  94  */
  95 
  96 /* ECC Fault Status Register layout:
  97  *
  98  * ----------------------------------------------
  99  * | RESV|C2E|MULT|SYNDROME|DWORD|UNC|TIMEO|BS|C|
 100  * ----------------------------------------------
 101  *  31-18  17  16    15-8    7-4   3    2    1 0
 102  *
 103  * C2E: A C2 graphics error occurred. 0=no 1=yes (SS10 only)
 104  * MULT: Multiple errors occurred ;-O 0=no 1=prom_panic(yes)
 105  * SYNDROME: Controller is mentally unstable.
 106  * DWORD:
 107  * UNC: Uncorrectable error.  0=no 1=yes
 108  * TIMEO: Timeout occurred. 0=no 1=yes
 109  * BS: C2 graphics bad slot access. 0=no 1=yes (SS10 only)
 110  * C: Correctable error? 0=no 1=yes
 111  */
 112 
 113 #define ECC_FSR_C2ERR    0x00020000
 114 #define ECC_FSR_MULT     0x00010000
 115 #define ECC_FSR_SYND     0x0000ff00
 116 #define ECC_FSR_DWORD    0x000000f0
 117 #define ECC_FSR_UNC      0x00000008
 118 #define ECC_FSR_TIMEO    0x00000004
 119 #define ECC_FSR_BADSLOT  0x00000002
 120 #define ECC_FSR_C        0x00000001
 121 
 122 #endif /* !(_SPARC_ECC_H) */

/* [previous][next][first][last][top][bottom][index][help] */