include/linux/xd.h

/* */
   1 #ifndef _LINUX_XD_H
   2 #define _LINUX_XD_H
   3 
   4 /*
   5  * This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X).
   6  *
   7  * Author: Pat Mackinlay, smackinla@cc.curtin.edu.au
   8  * Date: 29/09/92
   9  *
  10  * Revised: 01/01/93, ...
  11  *
  12  * Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com)
  13  * Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst.
  14  */
  15 
  16 /* XT hard disk controller registers */
  17 #define XD_DATA         (xd_iobase + 0x00)      /* data RW register */
  18 #define XD_RESET        (xd_iobase + 0x01)      /* reset WO register */
  19 #define XD_STATUS       (xd_iobase + 0x01)      /* status RO register */
  20 #define XD_SELECT       (xd_iobase + 0x02)      /* select WO register */
  21 #define XD_JUMPER       (xd_iobase + 0x02)      /* jumper RO register */
  22 #define XD_CONTROL      (xd_iobase + 0x03)      /* DMAE/INTE WO register */
  23 #define XD_RESERVED     (xd_iobase + 0x03)      /* reserved */
  24 
  25 /* XT hard disk controller commands (incomplete list) */
  26 #define CMD_TESTREADY   0x00    /* test drive ready */
  27 #define CMD_RECALIBRATE 0x01    /* recalibrate drive */
  28 #define CMD_SENSE       0x03    /* request sense */
  29 #define CMD_FORMATDRV   0x04    /* format drive */
  30 #define CMD_VERIFY      0x05    /* read verify */
  31 #define CMD_FORMATTRK   0x06    /* format track */
  32 #define CMD_FORMATBAD   0x07    /* format bad track */
  33 #define CMD_READ        0x08    /* read */
  34 #define CMD_WRITE       0x0A    /* write */
  35 #define CMD_SEEK        0x0B    /* seek */
  36 
  37 /* Controller specific commands */
  38 #define CMD_DTCSETPARAM 0x0C    /* set drive parameters (DTC 5150X only?) */
  39 #define CMD_DTCGETECC   0x0D    /* get ecc error length (DTC 5150X only?) */
  40 #define CMD_DTCREADBUF  0x0E    /* read sector buffer (DTC 5150X only?) */
  41 #define CMD_DTCWRITEBUF 0x0F    /* write sector buffer (DTC 5150X only?) */
  42 #define CMD_DTCREMAPTRK 0x11    /* assign alternate track (DTC 5150X only?) */
  43 #define CMD_DTCGETPARAM 0xFB    /* get drive parameters (DTC 5150X only?) */
  44 #define CMD_DTCSETSTEP  0xFC    /* set step rate (DTC 5150X only?) */
  45 #define CMD_DTCSETGEOM  0xFE    /* set geometry data (DTC 5150X only?) */
  46 #define CMD_DTCGETGEOM  0xFF    /* get geometry data (DTC 5150X only?) */
  47 #define CMD_ST11GETGEOM 0xF8    /* get geometry data (Seagate ST11R/M only?) */
  48 #define CMD_WDSETPARAM  0x0C    /* set drive parameters (WD 1004A27X only?) */
  49 
  50 /* Bits for command status byte */
  51 #define CSB_ERROR       0x02    /* error */
  52 #define CSB_LUN         0x20    /* logical Unit Number */
  53 
  54 /* XT hard disk controller status bits */
  55 #define STAT_READY      0x01    /* controller is ready */
  56 #define STAT_INPUT      0x02    /* data flowing from controller to host */
  57 #define STAT_COMMAND    0x04    /* controller in command phase */
  58 #define STAT_SELECT     0x08    /* controller is selected */
  59 #define STAT_REQUEST    0x10    /* controller requesting data */
  60 #define STAT_INTERRUPT  0x20    /* controller requesting interrupt */
  61 
  62 /* XT hard disk controller control bits */
  63 #define PIO_MODE        0x00    /* control bits to set for PIO */
  64 #define DMA_MODE        0x03    /* control bits to set for DMA & interrupt */
  65 
  66 #define XD_MAXDRIVES    2       /* maximum 2 drives */
  67 #define XD_TIMEOUT      100     /* 1 second timeout */
  68 #define XD_RETRIES      4       /* maximum 4 retries */
  69 
  70 #undef DEBUG                    /* define for debugging output */
  71 
  72 #ifdef DEBUG
  73         #define DEBUG_STARTUP   /* debug driver initialisation */
  74         #define DEBUG_OVERRIDE  /* debug override geometry detection */
  75         #define DEBUG_READWRITE /* debug each read/write command */
  76         #define DEBUG_OTHER     /* debug misc. interrupt/DMA stuff */
  77         #define DEBUG_COMMAND   /* debug each controller command */
  78 #endif /* DEBUG */
  79 
  80 /* this structure defines the XT drives and their types */
  81 typedef struct {
  82         u_char heads;
  83         u_short cylinders;
  84         u_char sectors;
  85         u_char control;
  86 } XD_INFO;
  87 
  88 #define HDIO_GETGEO     0x0301          /* get drive geometry */
  89 
  90 /* this structure is returned to the HDIO_GETGEO ioctl */
  91 typedef struct {
  92         u_char heads;
  93         u_char sectors;
  94         u_short cylinders;
  95         u_long start;
  96 } XD_GEOMETRY;
  97 
  98 /* this structure defines a ROM BIOS signature */
  99 typedef struct {
 100         u_long offset;
 101         char *string;
 102         void (*init_controller)(u_char *address);
 103         void (*init_drive)(u_char drive);
 104         char *name;
 105 } XD_SIGNATURE;
 106 
 107 u_long xd_init (u_long mem_start,u_long mem_end);
 108 void xd_setup (char *command,int *integers);
 109 static u_char xd_detect (u_char *controller,u_char **address);
 110 static u_char xd_initdrives (void (*init_drive)(u_char drive));
 111 static void xd_geninit (void);
 112 
 113 static int xd_open (struct inode *inode,struct file *file);
 114 static void do_xd_request (void);
 115 static int xd_ioctl (struct inode *inode,struct file *file,unsigned int cmd,unsigned long arg);
 116 static void xd_release (struct inode *inode,struct file *file);
 117 static int xd_reread_partitions (int dev);
 118 static int xd_readwrite (u_char operation,u_char drive,char *buffer,u_int block,u_int count);
 119 static void xd_recalibrate (u_char drive);
 120 
 121 static void xd_interrupt_handler (int unused);
 122 static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count);
 123 static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control);
 124 static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout);
 125 static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout);
 126 
 127 /* card specific setup and geometry gathering code */
 128 static void xd_dtc_init_controller (u_char *address);
 129 static void xd_dtc_init_drive (u_char drive);
 130 static void xd_wd_init_controller (u_char *address);
 131 static void xd_wd_init_drive (u_char drive);
 132 static void xd_seagate_init_controller (u_char *address);
 133 static void xd_seagate_init_drive (u_char drive);
 134 static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc);
 135 static void xd_override_init_drive (u_char drive);
 136 
 137 #endif /* _LINUX_XD_H */
/* */
root/include/linux/xd.h

INCLUDED FROM
