![[first]](../icons/first.png){kind=icon}
![[previous]](../icons/n_left.png){kind=icon}
![[next]](../icons/n_right.png){kind=icon}
![[last]](../icons/last.png){kind=icon}
![[top]](../icons/n_top.png){kind=icon}
![[bottom]](../icons/bottom.png){kind=icon}
![[index]](../icons/index.png){kind=icon}
![[help]](../icons/help.png){kind=icon}
*/
1 /* znet.c: An Zenith Z-Note ethernet driver for linux. */
2
3 static char *version = "znet.c:v1.01 7/1/94 becker@cesdis.gsfc.nasa.gov\n";
4
5 /*
6 Written by Donald Becker.
7
8 The author may be reached as becker@cesdis.gsfc.nasa.gov.
9 This driver is based on the Linux skeleton driver. The copyright of the
10 skeleton driver is held by the United States Government, as represented
11 by DIRNSA, and it is released under the GPL.
12
13 Thanks to Mike Hollick for alpha testing and suggestions.
14
15 References:
16 The Crynwr packet driver.
17
18 "82593 CSMA/CD Core LAN Controller" Intel datasheet, 1992
19 Intel Microcommunications Databook, Vol. 1, 1990.
20 As usual with Intel, the documentation is incomplete and inaccurate.
21 I had to read the Crynwr packet driver to figure out how to actually
22 use the i82593, and guess at what register bits matched the loosely
23 related i82586.
24
25 Theory of Operation
26
27 The i82593 used in the Zenith Z-Note series operates using two(!) slave
28 DMA channels, one interrupt, and one 8-bit I/O port.
29
30 While there several ways to configure '593 DMA system, I chose the one
31 that seemed commesurate with the highest system performance in the face
32 of moderate interrupt latency: Both DMA channels are configued as
33 recirculating ring buffers, with one channel (#0) dedicated to Rx and
34 the other channel (#1) to Tx and configuration. (Note that this is
35 different than the Crynwr driver, where the Tx DMA channel is initialized
36 before each operation. That approach simplifies operation and Tx error
37 recovery, but requires additional I/O in normal operation and precludes
38 transmit buffer chaining.)
39
40 Both rings are set to 8192 bytes using {TX,RX}_RING_SIZE. This provides
41 a reasonable ring size for Rx, while simplifying DMA buffer allocation --
42 DMA buffers must not cross a 128K boundary. (In truth the size selection
43 was influenced by my lack of '593 documentation. I thus was constrained
44 to use the Crynwr '593 initialization table, which sets the Rx ring size
45 to 8K.)
46
47 Despite my usual low opinion about Intel-designed parts, I must admit
48 that the bulk data handling of the i82593 is a good design for
49 an integrated system, like a laptop, where using two slave DMA channels
50 doesn't pose a problem. I still take issue with using only a single I/O
51 port. In the same controlled environment there are essentially no
52 limitations on I/O space, and using multiple locations would eliminate
53 the need for multiple operations when looking at status registers,
54 setting the Rx ring boundary, or switching to promiscuous mode.
55
56 I also question Zenith's selection of the '593: one of the advertised
57 advantages of earlier Intel parts was that if you figured out the magic
58 initialization incantation you could use the same part on many different
59 network types. Zenith's use of the "FriendlyNet" (sic) connector rather
60 than an on-board transceiver leads me to believe that they were planning
61 to take advantage of this. But, uhmmm, the '593 omits all but ethernet
62 functionality from the serial subsystem.
63 */
64
65 #include <linux/config.h>
66 #include <linux/kernel.h>
67 #include <linux/sched.h>
68 #include <linux/string.h>
69 #include <linux/ptrace.h>
70 #include <linux/errno.h>
71 #include <linux/interrupt.h>
72 #include <linux/ioport.h>
73 #include <asm/system.h>
74 #include <asm/bitops.h>
75 #include <asm/io.h>
76 #include <asm/dma.h>
77
78 #include <linux/netdevice.h>
79 #include <linux/etherdevice.h>
80 #include <linux/skbuff.h>
81 #include <linux/if_arp.h>
82
83 #ifndef ZNET_DEBUG
84 #define ZNET_DEBUG 3
85 #endif
86 static unsigned int znet_debug = ZNET_DEBUG;
87
88 /* The DMA modes we need aren't in <dma.h>. */
89 #define DMA_RX_MODE 0x14 /* Auto init, I/O to mem, ++, demand. */
90 #define DMA_TX_MODE 0x18 /* Auto init, Mem to I/O, ++, demand. */
91 #define dma_page_eq(ptr1, ptr2) ((long)(ptr1)>>17 == (long)(ptr2)>>17)
92 #define DMA_BUF_SIZE 8192
93 #define RX_BUF_SIZE 8192
94 #define TX_BUF_SIZE 8192
95
96 /* Commands to the i82593 channel 0. */
97 #define CMD0_CHNL_0 0x00
98 #define CMD0_CHNL_1 0x10 /* Switch to channel 1. */
99 #define CMD0_NOP (CMD0_CHNL_0)
100 #define CMD0_PORT_1 CMD0_CHNL_1
101 #define CMD1_PORT_0 1
102 #define CMD0_IA_SETUP 1
103 #define CMD0_CONFIGURE 2
104 #define CMD0_MULTICAST_LIST 3
105 #define CMD0_TRANSMIT 4
106 #define CMD0_DUMP 6
107 #define CMD0_DIAGNOSE 7
108 #define CMD0_Rx_ENABLE 8
109 #define CMD0_Rx_DISABLE 10
110 #define CMD0_Rx_STOP 11
111 #define CMD0_RETRANSMIT 12
112 #define CMD0_ABORT 13
113 #define CMD0_RESET 14
114
115 #define CMD0_ACK 0x80
116
117 #define CMD0_STAT0 (0 << 5)
118 #define CMD0_STAT1 (1 << 5)
119 #define CMD0_STAT2 (2 << 5)
120 #define CMD0_STAT3 (3 << 5)
121
122 #define net_local znet_private
123 struct znet_private {
124 int rx_dma, tx_dma;
125 struct enet_statistics stats;
126 /* The starting, current, and end pointers for the packet buffers. */
127 ushort *rx_start, *rx_cur, *rx_end;
128 ushort *tx_start, *tx_cur, *tx_end;
129 ushort tx_buf_len; /* Tx buffer lenght, in words. */
130 };
131
132 /* Only one can be built-in;-> */
133 static struct znet_private zn;
134 static ushort dma_buffer1[DMA_BUF_SIZE/2];
135 static ushort dma_buffer2[DMA_BUF_SIZE/2];
136 static ushort dma_buffer3[DMA_BUF_SIZE/2 + 8];
137
138 /* The configuration block. What an undocumented nightmare. The first
139 set of values are those suggested (without explaination) for ethernet
140 in the Intel 82586 databook. The rest appear to be completely undocumented,
141 except for cryptic notes in the Crynwr packet driver. This driver uses
142 the Crynwr values verbatim. */
143
144 static unsigned char i593_init[] = {
145 0xAA, /* 0: 16-byte input & 80-byte output FIFO. */
146 /* threshhold, 96-byte FIFO, 82593 mode. */
147 0x88, /* 1: Continuous w/interrupts, 128-clock DMA.*/
148 0x2E, /* 2: 8-byte preamble, NO address insertion, */
149 /* 6-byte Ethernet address, loopback off.*/
150 0x00, /* 3: Default priorities & backoff methods. */
151 0x60, /* 4: 96-bit interframe spacing. */
152 0x00, /* 5: 512-bit slot time (low-order). */
153 0xF2, /* 6: Slot time (high-order), 15 COLL retries. */
154 0x00, /* 7: Promisc-off, broadcast-on, default CRC. */
155 0x00, /* 8: Default carrier-sense, collision-detect. */
156 0x40, /* 9: 64-byte minimum frame length. */
157 0x5F, /* A: Type/length checks OFF, no CRC input,
158 "jabber" termination, etc. */
159 0x00, /* B: Full-duplex disabled. */
160 0x3F, /* C: Default multicast addresses & backoff. */
161 0x07, /* D: Default IFS retriggering. */
162 0x31, /* E: Internal retransmit, drop "runt" packets,
163 synchr. DRQ deassertion, 6 status bytes. */
164 0x22, /* F: Receive ring-buffer size (8K),
165 receive-stop register enable. */
166 };
167
168 struct netidblk {
169 char magic[8]; /* The magic number (string) "NETIDBLK" */
170 unsigned char netid[8]; /* The physical station address */
171 char nettype, globalopt;
172 char vendor[8]; /* The machine vendor and product name. */
173 char product[8];
174 char irq1, irq2; /* Interrupts, only one is currently used. */
175 char dma1, dma2;
176 short dma_mem_misc[8]; /* DMA buffer locations (unused in Linux). */
177 short iobase1, iosize1;
178 short iobase2, iosize2; /* Second iobase unused. */
179 char driver_options; /* Misc. bits */
180 char pad;
181 };
182
183 int znet_probe(struct device *dev);
184 static int znet_open(struct device *dev);
185 static int znet_send_packet(struct sk_buff *skb, struct device *dev);
186 static void znet_interrupt(int reg_ptr);
187 static void znet_rx(struct device *dev);
188 static int znet_close(struct device *dev);
189 static struct enet_statistics *net_get_stats(struct device *dev);
190 static void set_multicast_list(struct device *dev, int num_addrs, void *addrs);
191 static void hardware_init(struct device *dev);
192 static void update_stop_hit(short ioaddr, unsigned short rx_stop_offset);
193
194 #ifdef notdef
195 static struct sigaction znet_sigaction = { &znet_interrupt, 0, 0, NULL, };
196 #endif
197
198
199 /* The Z-Note probe is pretty easy. The NETIDBLK exists in the safe-to-probe
200 BIOS area. We just scan for the signature, and pull the vital parameters
201 out of the structure. */
202
203 int znet_probe(struct device *dev)
/* ![[next]](../icons/right.png)
![[first]](../icons/n_first.png)
![[top]](../icons/top.png)
*/
204 {
205 int i;
206 struct netidblk *netinfo;
207 char *p;
208
209 /* This code scans the region 0xf0000 to 0xfffff for a "NETIDBLK". */
210 for(p = (char *)0xf0000; p < (char *)0x100000; p++)
211 if (*p == 'N' && strncmp(p, "NETIDBLK", 8) == 0)
212 break;
213
214 if (p >= (char *)0x100000) {
215 if (znet_debug > 1)
216 printk(KERN_INFO "No Z-Note ethernet adaptor found.\n");
217 return ENODEV;
218 }
219 netinfo = (struct netidblk *)p;
220 dev->base_addr = netinfo->iobase1;
221 dev->irq = netinfo->irq1;
222
223 printk(KERN_INFO "%s: ZNET at %#3x,", dev->name, dev->base_addr);
224
225 /* The station address is in the "netidblk" at 0x0f0000. */
226 for (i = 0; i < 6; i++)
227 printk(" %2.2x", dev->dev_addr[i] = netinfo->netid[i]);
228
229 printk(", using IRQ %d DMA %d and %d.\n", dev->irq, netinfo->dma1,
230 netinfo->dma2);
231
232 if (znet_debug > 1) {
233 printk(KERN_INFO "%s: vendor '%16.16s' IRQ1 %d IRQ2 %d DMA1 %d DMA2 %d.\n",
234 dev->name, netinfo->vendor,
235 netinfo->irq1, netinfo->irq2,
236 netinfo->dma1, netinfo->dma2);
237 printk(KERN_INFO "%s: iobase1 %#x size %d iobase2 %#x size %d net type %2.2x.\n",
238 dev->name, netinfo->iobase1, netinfo->iosize1,
239 netinfo->iobase2, netinfo->iosize2, netinfo->nettype);
240 }
241
242 if (znet_debug > 0)
243 printk("%s%s", KERN_INFO, version);
244
245 dev->priv = (void *) &zn;
246 zn.rx_dma = netinfo->dma1;
247 zn.tx_dma = netinfo->dma2;
248
249 /* These should never fail. You can't add devices to a sealed box! */
250 if (request_irq(dev->irq, &znet_interrupt)
251 || request_dma(zn.rx_dma)
252 || request_dma(zn.tx_dma)) {
253 printk(KERN_WARNING "%s: Not opened -- resource busy?!?\n", dev->name);
254 return EBUSY;
255 }
256 irq2dev_map[dev->irq] = dev;
257
258 /* Allocate buffer memory. We can cross a 128K boundary, so we
259 must be careful about the allocation. It's easiest to waste 8K. */
260 if (dma_page_eq(dma_buffer1, &dma_buffer1[RX_BUF_SIZE/2-1]))
261 zn.rx_start = dma_buffer1;
262 else
263 zn.rx_start = dma_buffer2;
264
265 if (dma_page_eq(dma_buffer3, &dma_buffer3[RX_BUF_SIZE/2-1]))
266 zn.tx_start = dma_buffer3;
267 else
268 zn.tx_start = dma_buffer2;
269 zn.rx_end = zn.rx_start + RX_BUF_SIZE/2;
270 zn.tx_buf_len = TX_BUF_SIZE/2;
271 zn.tx_end = zn.tx_start + zn.tx_buf_len;
272
273 /* The ZNET-specific entries in the device structure. */
274 dev->open = &znet_open;
275 dev->hard_start_xmit = &znet_send_packet;
276 dev->stop = &znet_close;
277 dev->get_stats = net_get_stats;
278 dev->set_multicast_list = &set_multicast_list;
279
280 /* Fill in the 'dev' with ethernet-generic values. */
281 ether_setup(dev);
282
283 return 0;
284 }
285
286
287 static int znet_open(struct device *dev)
/* ![[previous]](../icons/left.png)
*/
288 {
289 int ioaddr = dev->base_addr;
290
291 if (znet_debug > 2)
292 printk(KERN_DEBUG "%s: znet_open() called.\n", dev->name);
293
294 /* Turn on the 82501 SIA, using zenith-specific magic. */
295 outb(0x10, 0xe6); /* Select LAN control register */
296 outb(inb(0xe7) | 0x84, 0xe7); /* Turn on LAN power (bit 2). */
297 /* According to the Crynwr driver we should wait 50 msec. for the
298 LAN clock to stabilize. My experiments indicates that the '593 can
299 be initialized immediately. The delay is probably needed for the
300 DC-to-DC converter to come up to full voltage, and for the oscillator
301 to be spot-on at 20Mhz before transmitting.
302 Until this proves to be a problem we rely on the higher layers for the
303 delay and save allocating a timer entry. */
304
305 /* This follows the packet driver's lead, and checks for success. */
306 if (inb(ioaddr) != 0x10 && inb(ioaddr) != 0x00)
307 printk(KERN_WARNING "%s: Problem turning on the transceiver power.\n",
308 dev->name);
309
310 dev->tbusy = 0;
311 dev->interrupt = 0;
312 hardware_init(dev);
313 dev->start = 1;
314
315 return 0;
316 }
317
318 static int znet_send_packet(struct sk_buff *skb, struct device *dev)
/* */
319 {
320 int ioaddr = dev->base_addr;
321
322 if (znet_debug > 4)
323 printk(KERN_DEBUG "%s: ZNet_send_packet(%d).\n", dev->name, dev->tbusy);
324
325 /* Transmitter timeout, likely just recovery after suspending the machine. */
326 if (dev->tbusy) {
327 ushort event, tx_status, rx_offset, state;
328 int tickssofar = jiffies - dev->trans_start;
329 if (tickssofar < 10)
330 return 1;
331 outb(CMD0_STAT0, ioaddr); event = inb(ioaddr);
332 outb(CMD0_STAT1, ioaddr); tx_status = inw(ioaddr);
333 outb(CMD0_STAT2, ioaddr); rx_offset = inw(ioaddr);
334 outb(CMD0_STAT3, ioaddr); state = inb(ioaddr);
335 printk(KERN_WARNING "%s: transmit timed out, status %02x %04x %04x %02x,"
336 " resetting.\n", dev->name, event, tx_status, rx_offset, state);
337 if (tx_status == 0x0400)
338 printk(KERN_WARNING "%s: Tx carrier error, check transceiver cable.\n",
339 dev->name);
340 outb(CMD0_RESET, ioaddr);
341 hardware_init(dev);
342 }
343
344 if (skb == NULL) {
345 dev_tint(dev);
346 return 0;
347 }
348
349 /* Check that the part hasn't reset itself, probably from suspend. */
350 outb(CMD0_STAT0, ioaddr);
351 if (inw(ioaddr) == 0x0010
352 && inw(ioaddr) == 0x0000
353 && inw(ioaddr) == 0x0010)
354 hardware_init(dev);
355
356 /* Block a timer-based transmit from overlapping. This could better be
357 done with atomic_swap(1, dev->tbusy), but set_bit() works as well. */
358 if (set_bit(0, (void*)&dev->tbusy) != 0)
359 printk(KERN_WARNING "%s: Transmitter access conflict.\n", dev->name);
360 else {
361 short length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN;
362 unsigned char *buf = (void *)(skb+1);
363 ushort *tx_link = zn.tx_cur - 1;
364 ushort rnd_len = (length + 1)>>1;
365
366 {
367 short dma_port = ((zn.tx_dma&3)<<2) + IO_DMA2_BASE;
368 unsigned addr = inb(dma_port);
369 addr |= inb(dma_port) << 8;
370 addr <<= 1;
371 if (((int)zn.tx_cur & 0x1ffff) != addr)
372 printk(KERN_WARNING "Address mismatch at Tx: %#x vs %#x.\n",
373 (int)zn.tx_cur & 0xffff, addr);
374 zn.tx_cur = (ushort *)(((int)zn.tx_cur & 0xfe0000) | addr);
375 }
376
377 if (zn.tx_cur >= zn.tx_end)
378 zn.tx_cur = zn.tx_start;
379 *zn.tx_cur++ = length;
380 if (zn.tx_cur + rnd_len + 1 > zn.tx_end) {
381 int semi_cnt = (zn.tx_end - zn.tx_cur)<<1; /* Cvrt to byte cnt. */
382 memcpy(zn.tx_cur, buf, semi_cnt);
383 rnd_len -= semi_cnt>>1;
384 memcpy(zn.tx_start, buf + semi_cnt, length - semi_cnt);
385 zn.tx_cur = zn.tx_start + rnd_len;
386 } else {
387 memcpy(zn.tx_cur, buf, skb->len);
388 zn.tx_cur += rnd_len;
389 }
390 *zn.tx_cur++ = 0;
391 cli(); {
392 *tx_link = CMD0_TRANSMIT + CMD0_CHNL_1;
393 /* Is this always safe to do? */
394 outb(CMD0_TRANSMIT + CMD0_CHNL_1,ioaddr);
395 } sti();
396
397 dev->trans_start = jiffies;
398 if (znet_debug > 4)
399 printk(KERN_DEBUG "%s: Transmitter queued, length %d.\n", dev->name, length);
400 }
401 dev_kfree_skb(skb, FREE_WRITE);
402 return 0;
403 }
404
405 /* The ZNET interrupt handler. */
406 static void znet_interrupt(int reg_ptr)
/* */
407 {
408 int irq = -(((struct pt_regs *)reg_ptr)->orig_eax+2);
409 struct device *dev = irq2dev_map[irq];
410 int ioaddr;
411 int boguscnt = 20;
412
413 if (dev == NULL) {
414 printk(KERN_WARNING "znet_interrupt(): IRQ %d for unknown device.\n", irq);
415 return;
416 }
417
418 dev->interrupt = 1;
419 ioaddr = dev->base_addr;
420
421 outb(CMD0_STAT0, ioaddr);
422 do {
423 ushort status = inb(ioaddr);
424 if (znet_debug > 5) {
425 ushort result, rx_ptr, running;
426 outb(CMD0_STAT1, ioaddr);
427 result = inw(ioaddr);
428 outb(CMD0_STAT2, ioaddr);
429 rx_ptr = inw(ioaddr);
430 outb(CMD0_STAT3, ioaddr);
431 running = inb(ioaddr);
432 printk(KERN_DEBUG "%s: interrupt, status %02x, %04x %04x %02x serial %d.\n",
433 dev->name, status, result, rx_ptr, running, boguscnt);
434 }
435 if ((status & 0x80) == 0)
436 break;
437
438 if ((status & 0x0F) == 4) { /* Transmit done. */
439 struct net_local *lp = (struct net_local *)dev->priv;
440 int tx_status;
441 outb(CMD0_STAT1, ioaddr);
442 tx_status = inw(ioaddr);
443 /* It's undocumented, but tx_status seems to match the i82586. */
444 if (tx_status & 0x2000) {
445 lp->stats.tx_packets++;
446 lp->stats.collisions += tx_status & 0xf;
447 } else {
448 if (tx_status & 0x0600) lp->stats.tx_carrier_errors++;
449 if (tx_status & 0x0100) lp->stats.tx_fifo_errors++;
450 if (!(tx_status & 0x0040)) lp->stats.tx_heartbeat_errors++;
451 if (tx_status & 0x0020) lp->stats.tx_aborted_errors++;
452 /* ...and the catch-all. */
453 if (tx_status | 0x0760 != 0x0760)
454 lp->stats.tx_errors++;
455 }
456 dev->tbusy = 0;
457 mark_bh(NET_BH); /* Inform upper layers. */
458 }
459
460 if ((status & 0x40)
461 || (status & 0x0f) == 11) {
462 znet_rx(dev);
463 }
464 /* Clear the interrupts we've handled. */
465 outb(CMD0_ACK,ioaddr);
466 } while (boguscnt--);
467
468 dev->interrupt = 0;
469 return;
470 }
471
472 static void znet_rx(struct device *dev)
/* */
473 {
474 struct net_local *lp = (struct net_local *)dev->priv;
475 int ioaddr = dev->base_addr;
476 int boguscount = 1;
477 short next_frame_end_offset = 0; /* Offset of next frame start. */
478 short *cur_frame_end;
479 short cur_frame_end_offset;
480
481 outb(CMD0_STAT2, ioaddr);
482 cur_frame_end_offset = inw(ioaddr);
483
484 if (cur_frame_end_offset == zn.rx_cur - zn.rx_start) {
485 printk(KERN_WARNING "%s: Interrupted, but nothing to receive, offset %03x.\n",
486 dev->name, cur_frame_end_offset);
487 return;
488 }
489
490 /* Use same method as the Crynwr driver: construct a forward list in
491 the same area of the backwards links we now have. This allows us to
492 pass packets to the upper layers in the order they were received --
493 important for fast-path sequential operations. */
494 while (zn.rx_start + cur_frame_end_offset != zn.rx_cur
495 && ++boguscount < 5) {
496 unsigned short hi_cnt, lo_cnt, hi_status, lo_status;
497 int count, status;
498
499 if (cur_frame_end_offset < 4) {
500 /* Oh no, we have a special case: the frame trailer wraps around
501 the end of the ring buffer. We've saved space at the end of
502 the ring buffer for just this problem. */
503 memcpy(zn.rx_end, zn.rx_start, 8);
504 cur_frame_end_offset += (RX_BUF_SIZE/2);
505 }
506 cur_frame_end = zn.rx_start + cur_frame_end_offset - 4;
507
508 lo_status = *cur_frame_end++;
509 hi_status = *cur_frame_end++;
510 status = ((hi_status & 0xff) << 8) + (lo_status & 0xff);
511 lo_cnt = *cur_frame_end++;
512 hi_cnt = *cur_frame_end++;
513 count = ((hi_cnt & 0xff) << 8) + (lo_cnt & 0xff);
514
515 if (znet_debug > 5)
516 printk(KERN_DEBUG "Constructing trailer at location %03x, %04x %04x %04x %04x"
517 " count %#x status %04x.\n",
518 cur_frame_end_offset<<1, lo_status, hi_status, lo_cnt, hi_cnt,
519 count, status);
520 cur_frame_end[-4] = status;
521 cur_frame_end[-3] = next_frame_end_offset;
522 cur_frame_end[-2] = count;
523 next_frame_end_offset = cur_frame_end_offset;
524 cur_frame_end_offset -= ((count + 1)>>1) + 3;
525 if (cur_frame_end_offset < 0)
526 cur_frame_end_offset += RX_BUF_SIZE/2;
527 };
528
529 /* Now step forward through the list. */
530 do {
531 ushort *this_rfp_ptr = zn.rx_start + next_frame_end_offset;
532 int status = this_rfp_ptr[-4];
533 int pkt_len = this_rfp_ptr[-2];
534
535 if (znet_debug > 5)
536 printk(KERN_DEBUG "Looking at trailer ending at %04x status %04x length %03x"
537 " next %04x.\n", next_frame_end_offset<<1, status, pkt_len,
538 this_rfp_ptr[-3]<<1);
539 /* Once again we must assume that the i82586 docs apply. */
540 if ( ! (status & 0x2000)) { /* There was an error. */
541 lp->stats.rx_errors++;
542 if (status & 0x0800) lp->stats.rx_crc_errors++;
543 if (status & 0x0400) lp->stats.rx_frame_errors++;
544 if (status & 0x0200) lp->stats.rx_over_errors++; /* Wrong. */
545 if (status & 0x0100) lp->stats.rx_fifo_errors++;
546 if (status & 0x0080) lp->stats.rx_length_errors++;
547 } else if (pkt_len > 1536) {
548 lp->stats.rx_length_errors++;
549 } else {
550 /* Malloc up new buffer. */
551 int sksize = sizeof(struct sk_buff) + pkt_len;
552 struct sk_buff *skb;
553
554 skb = alloc_skb(sksize, GFP_ATOMIC);
555 if (skb == NULL) {
556 if (znet_debug)
557 printk(KERN_WARNING "%s: Memory squeeze, dropping packet.\n", dev->name);
558 lp->stats.rx_dropped++;
559 break;
560 }
561 skb->mem_len = sksize;
562 skb->mem_addr = skb;
563 skb->len = pkt_len;
564 skb->dev = dev;
565
566 if (&zn.rx_cur[(pkt_len+1)>>1] > zn.rx_end) {
567 int semi_cnt = (zn.rx_end - zn.rx_cur)<<1;
568 memcpy((unsigned char *) (skb + 1), zn.rx_cur, semi_cnt);
569 memcpy((unsigned char *) (skb + 1) + semi_cnt, zn.rx_start,
570 pkt_len - semi_cnt);
571 } else {
572 memcpy((unsigned char *) (skb + 1), zn.rx_cur, pkt_len);
573 if (znet_debug > 6) {
574 unsigned int *packet = (unsigned int *) (skb + 1);
575 printk(KERN_DEBUG "Packet data is %08x %08x %08x %08x.\n", packet[0],
576 packet[1], packet[2], packet[3]);
577 }
578 }
579
580 #ifdef HAVE_NETIF_RX
581 netif_rx(skb);
582 #else
583 skb->lock = 0;
584 if (dev_rint((unsigned char*)skb, pkt_len, IN_SKBUFF, dev) != 0) {
585 kfree_s(skb, sksize);
586 lp->stats.rx_dropped++;
587 break;
588 }
589 #endif
590 lp->stats.rx_packets++;
591 }
592 zn.rx_cur = this_rfp_ptr;
593 if (zn.rx_cur >= zn.rx_end)
594 zn.rx_cur -= RX_BUF_SIZE/2;
595 update_stop_hit(ioaddr, (zn.rx_cur - zn.rx_start)<<1);
596 next_frame_end_offset = this_rfp_ptr[-3];
597 if (next_frame_end_offset == 0) /* Read all the frames? */
598 break; /* Done for now */
599 this_rfp_ptr = zn.rx_start + next_frame_end_offset;
600 } while (--boguscount);
601
602 /* If any worth-while packets have been received, dev_rint()
603 has done a mark_bh(INET_BH) for us and will work on them
604 when we get to the bottom-half routine. */
605 return;
606 }
607
608 /* The inverse routine to znet_open(). */
609 static int znet_close(struct device *dev)
/* */
610 {
611 int ioaddr = dev->base_addr;
612
613 dev->tbusy = 1;
614 dev->start = 0;
615
616 outb(CMD0_RESET, ioaddr); /* CMD0_RESET */
617
618 disable_dma(zn.rx_dma);
619 disable_dma(zn.tx_dma);
620
621 free_irq(dev->irq);
622
623 if (znet_debug > 1)
624 printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name);
625 /* Turn off transceiver power. */
626 outb(0x10, 0xe6); /* Select LAN control register */
627 outb(inb(0xe7) & ~0x84, 0xe7); /* Turn on LAN power (bit 2). */
628
629 return 0;
630 }
631
632 /* Get the current statistics. This may be called with the card open or
633 closed. */
634 static struct enet_statistics *net_get_stats(struct device *dev)
/* */
635 {
636 struct net_local *lp = (struct net_local *)dev->priv;
637
638 return &lp->stats;
639 }
640
641 #ifdef HAVE_MULTICAST
642 /* Set or clear the multicast filter for this adaptor.
643 num_addrs == -1 Promiscuous mode, receive all packets
644 num_addrs == 0 Normal mode, clear multicast list
645 num_addrs > 0 Multicast mode, receive normal and MC packets, and do
646 best-effort filtering.
647 As a side effect this routine must also initialize the device parameters.
648 This is taken advantage of in open().
649
650 N.B. that we change i593_init[] in place. This (properly) makes the
651 mode change persistent, but must be changed if this code is moved to
652 a multiple adaptor environment.
653 */
654 static void set_multicast_list(struct device *dev, int num_addrs, void *addrs)
/* */
655 {
656 short ioaddr = dev->base_addr;
657
658 if (num_addrs < 0) {
659 /* Enable promiscuous mode */
660 i593_init[7] &= ~3; i593_init[7] |= 1;
661 i593_init[13] &= ~8; i593_init[13] |= 8;
662 } else if (num_addrs > 0) {
663 /* Enable accept-all-multicast mode */
664 i593_init[7] &= ~3; i593_init[7] |= 0;
665 i593_init[13] &= ~8; i593_init[13] |= 8;
666 } else { /* Enable normal mode. */
667 i593_init[7] &= ~3; i593_init[7] |= 0;
668 i593_init[13] &= ~8; i593_init[13] |= 0;
669 }
670 *zn.tx_cur++ = sizeof(i593_init);
671 memcpy(zn.tx_cur, i593_init, sizeof(i593_init));
672 zn.tx_cur += sizeof(i593_init)/2;
673 outb(CMD0_CONFIGURE+CMD0_CHNL_1, ioaddr);
674 #ifdef not_tested
675 if (num_addrs > 0) {
676 int addrs_len = 6*num_addrs;
677 *zn.tx_cur++ = addrs_len;
678 memcpy(zn.tx_cur, addrs, addrs_len);
679 outb(CMD0_MULTICAST_LIST+CMD0_CHNL_1, ioaddr);
680 zn.tx_cur += addrs_len>>1;
681 }
682 #endif
683 }
684 #endif
685
686 void show_dma(void)
/* */
687 {
688 short dma_port = ((zn.tx_dma&3)<<2) + IO_DMA2_BASE;
689 unsigned addr = inb(dma_port);
690 addr |= inb(dma_port) << 8;
691 printk("Addr: %04x cnt:%3x...", addr<<1, get_dma_residue(zn.tx_dma));
692 }
693
694 /* Initialize the hardware. We have to do this when the board is open()ed
695 or when we come out of suspend mode. */
696 static void hardware_init(struct device *dev)
/* */
697 {
698 short ioaddr = dev->base_addr;
699
700 zn.rx_cur = zn.rx_start;
701 zn.tx_cur = zn.tx_start;
702
703 /* Reset the chip, and start it up. */
704 outb(CMD0_RESET, ioaddr);
705
706 cli(); { /* Protect against a DMA flip-flop */
707 disable_dma(zn.rx_dma); /* reset by an interrupting task. */
708 clear_dma_ff(zn.rx_dma);
709 set_dma_mode(zn.rx_dma, DMA_RX_MODE);
710 set_dma_addr(zn.rx_dma, (unsigned int) zn.rx_start);
711 set_dma_count(zn.rx_dma, RX_BUF_SIZE);
712 enable_dma(zn.rx_dma);
713 /* Now set up the Tx channel. */
714 disable_dma(zn.tx_dma);
715 clear_dma_ff(zn.tx_dma);
716 set_dma_mode(zn.tx_dma, DMA_TX_MODE);
717 set_dma_addr(zn.tx_dma, (unsigned int) zn.tx_start);
718 set_dma_count(zn.tx_dma, zn.tx_buf_len<<1);
719 enable_dma(zn.tx_dma);
720 } sti();
721
722 if (znet_debug > 1)
723 printk(KERN_DEBUG "%s: Initializing the i82593, tx buf %p... ", dev->name,
724 zn.tx_start);
725 /* Do an empty configure command, just like the Crynwr driver. This
726 resets to chip to its default values. */
727 *zn.tx_cur++ = 0;
728 *zn.tx_cur++ = 0;
729 printk("stat:%02x ", inb(ioaddr)); show_dma();
730 outb(CMD0_CONFIGURE+CMD0_CHNL_1, ioaddr);
731 *zn.tx_cur++ = sizeof(i593_init);
732 memcpy(zn.tx_cur, i593_init, sizeof(i593_init));
733 zn.tx_cur += sizeof(i593_init)/2;
734 printk("stat:%02x ", inb(ioaddr)); show_dma();
735 outb(CMD0_CONFIGURE+CMD0_CHNL_1, ioaddr);
736 *zn.tx_cur++ = 6;
737 memcpy(zn.tx_cur, dev->dev_addr, 6);
738 zn.tx_cur += 3;
739 printk("stat:%02x ", inb(ioaddr)); show_dma();
740 outb(CMD0_IA_SETUP + CMD0_CHNL_1, ioaddr);
741 printk("stat:%02x ", inb(ioaddr)); show_dma();
742
743 update_stop_hit(ioaddr, 8192);
744 if (znet_debug > 1) printk("enabling Rx.\n");
745 outb(CMD0_Rx_ENABLE+CMD0_CHNL_0, ioaddr);
746 dev->tbusy = 0;
747 }
748
749 static void update_stop_hit(short ioaddr, unsigned short rx_stop_offset)
/* ![[last]](../icons/n_last.png)
*/
750 {
751 outb(CMD0_PORT_1, ioaddr);
752 if (znet_debug > 5)
753 printk(KERN_DEBUG "Updating stop hit with value %02x.\n",
754 (rx_stop_offset >> 6) | 0x80);
755 outb((rx_stop_offset >> 6) | 0x80, ioaddr);
756 outb(CMD1_PORT_0, ioaddr);
757 }
758
759 /*
760 * Local variables:
761 * compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c znet.c"
762 * version-control: t
763 * kept-new-versions: 5
764 * c-indent-level: 4
765 * tab-width: 4
766 * End:
767 */
![[bottom]](../icons/n_bottom.png){kind=icon}
*/