include/linux/fdreg.h

/* */
   1 #ifndef _LINUX_FDREG_H
   2 #define _LINUX_FDREG_H
   3 /*
   4  * This file contains some defines for the floppy disk controller.
   5  * Various sources. Mostly "IBM Microcomputers: A Programmers
   6  * Handbook", Sanches and Canton.
   7  */
   8 
   9 #ifdef FDPATCHES
  10 
  11 #define FD_IOPORT fdc_state[fdc].address
  12 
  13 /* Fd controller regs. S&C, about page 340 */
  14 #define FD_STATUS       (4 + FD_IOPORT )
  15 #define FD_DATA         (5 + FD_IOPORT )
  16 
  17 /* Digital Output Register */
  18 #define FD_DOR          (2 + FD_IOPORT )
  19 
  20 /* Digital Input Register (read) */
  21 #define FD_DIR          (7 + FD_IOPORT )
  22 
  23 /* Diskette Control Register (write)*/
  24 #define FD_DCR          (7 + FD_IOPORT )
  25 
  26 #else
  27 
  28 #define FD_STATUS       0x3f4
  29 #define FD_DATA         0x3f5
  30 #define FD_DOR          0x3f2           /* Digital Output Register */
  31 #define FD_DIR          0x3f7           /* Digital Input Register (read) */
  32 #define FD_DCR          0x3f7           /* Diskette Control Register (write)*/
  33 
  34 #endif
  35 
  36 /* Bits of main status register */
  37 #define STATUS_BUSYMASK 0x0F            /* drive busy mask */
  38 #define STATUS_BUSY     0x10            /* FDC busy */
  39 #define STATUS_DMA      0x20            /* 0- DMA mode */
  40 #define STATUS_DIR      0x40            /* 0- cpu->fdc */
  41 #define STATUS_READY    0x80            /* Data reg ready */
  42 
  43 /* Bits of FD_ST0 */
  44 #define ST0_DS          0x03            /* drive select mask */
  45 #define ST0_HA          0x04            /* Head (Address) */
  46 #define ST0_NR          0x08            /* Not Ready */
  47 #define ST0_ECE         0x10            /* Equipment chech error */
  48 #define ST0_SE          0x20            /* Seek end */
  49 #define ST0_INTR        0xC0            /* Interrupt code mask */
  50 
  51 /* Bits of FD_ST1 */
  52 #define ST1_MAM         0x01            /* Missing Address Mark */
  53 #define ST1_WP          0x02            /* Write Protect */
  54 #define ST1_ND          0x04            /* No Data - unreadable */
  55 #define ST1_OR          0x10            /* OverRun */
  56 #define ST1_CRC         0x20            /* CRC error in data or addr */
  57 #define ST1_EOC         0x80            /* End Of Cylinder */
  58 
  59 /* Bits of FD_ST2 */
  60 #define ST2_MAM         0x01            /* Missing Address Mark (again) */
  61 #define ST2_BC          0x02            /* Bad Cylinder */
  62 #define ST2_SNS         0x04            /* Scan Not Satisfied */
  63 #define ST2_SEH         0x08            /* Scan Equal Hit */
  64 #define ST2_WC          0x10            /* Wrong Cylinder */
  65 #define ST2_CRC         0x20            /* CRC error in data field */
  66 #define ST2_CM          0x40            /* Control Mark = deleted */
  67 
  68 /* Bits of FD_ST3 */
  69 #define ST3_HA          0x04            /* Head (Address) */
  70 #define ST3_DS          0x08            /* drive is double-sided */
  71 #define ST3_TZ          0x10            /* Track Zero signal (1=track 0) */
  72 #define ST3_RY          0x20            /* drive is ready */
  73 #define ST3_WP          0x40            /* Write Protect */
  74 #define ST3_FT          0x80            /* Drive Fault */
  75 
  76 /* Values for FD_COMMAND */
  77 #define FD_RECALIBRATE          0x07    /* move to track 0 */
  78 #define FD_SEEK                 0x0F    /* seek track */
  79 #define FD_READ                 0xE6    /* read with MT, MFM, SKip deleted */
  80 #define FD_WRITE                0xC5    /* write with MT, MFM */
  81 #define FD_SENSEI               0x08    /* Sense Interrupt Status */
  82 #define FD_SPECIFY              0x03    /* specify HUT etc */
  83 #define FD_FORMAT               0x4D    /* format one track */
  84 #define FD_VERSION              0x10    /* get version code */
  85 #define FD_CONFIGURE            0x13    /* configure FIFO operation */
  86 #define FD_PERPENDICULAR        0x12    /* perpendicular r/w mode */
  87 #define FD_GETSTATUS            0x04    /* read ST3 */
  88 #define FD_DUMPREGS             0x0E    /* dump the contents of the fdc regs */
  89 #define FD_READID               0xEA    /* prints the header of a sector */
  90 #define FD_UNLOCK               0x14    /* Fifo config unlock */
  91 #define FD_LOCK                 0x94    /* Fifo config lock */
  92 #define FD_RSEEK_OUT            0x8f    /* seek out (i.e. to lower tracks) */
  93 #define FD_RSEEK_IN             0xcf    /* seek in (i.e. to higher tracks) */
  94 
  95 /* DMA commands */
  96 #define DMA_READ        0x46
  97 #define DMA_WRITE       0x4A
  98 
  99 /* FDC version return types */
 100 #define FDC_NONE        0x00
 101 #define FDC_UNKNOWN     0x10
 102 #define FDC_8272A       0x20    /* Intel 8272a, NEC 765 */
 103 #define FDC_765ED       0x30    /* Non-Intel 1MB-compatible FDC, can't detect */
 104 #define FDC_82072       0x40    /* Intel 82072; 8272a + FIFO + DUMPREGS */
 105 #define FDC_82077_ORIG  0x50    /* Original version of 82077AA, sans LOCK */
 106 #define FDC_82077       0x52    /* 82077AA-1 */
 107 
 108 #define FD_RESET_DELAY 20
 109 #endif
/* */
root/include/linux/fdreg.h

INCLUDED FROM
