![[first]](../icons/first.png){kind=icon}
![[previous]](../icons/n_left.png){kind=icon}
![[next]](../icons/n_right.png){kind=icon}
![[last]](../icons/last.png){kind=icon}
![[top]](../icons/n_top.png){kind=icon}
![[bottom]](../icons/bottom.png){kind=icon}
![[index]](../icons/index.png){kind=icon}
![[help]](../icons/help.png){kind=icon}
*/
1 /* tulip.c: A DEC 21040 ethernet driver for linux. */
2 /*
3 NOTICE: this version works with kernels 1.1.82 and later only!
4 Written 1994,1995 by Donald Becker.
5
6 This software may be used and distributed according to the terms
7 of the GNU Public License, incorporated herein by reference.
8
9 This driver is for the SMC EtherPower PCI ethernet adapter.
10 It should work with most other DEC 21*40-based ethercards.
11
12 The author may be reached as becker@CESDIS.gsfc.nasa.gov, or C/O
13 Center of Excellence in Space Data and Information Sciences
14 Code 930.5, Goddard Space Flight Center, Greenbelt MD 20771
15 */
16
17 static char *version = "tulip.c:v0.05 1/20/95 becker@cesdis.gsfc.nasa.gov\n";
18
19 #include <linux/config.h>
20 #include <linux/kernel.h>
21 #include <linux/sched.h>
22 #include <linux/string.h>
23 #include <linux/ptrace.h>
24 #include <linux/errno.h>
25 #include <linux/ioport.h>
26 #include <linux/malloc.h>
27 #include <linux/interrupt.h>
28 #include <linux/pci.h>
29 #include <linux/bios32.h>
30 #include <asm/bitops.h>
31 #include <asm/io.h>
32 #include <asm/dma.h>
33
34 #include <linux/netdevice.h>
35 #include <linux/etherdevice.h>
36 #include <linux/skbuff.h>
37
38 /* This will be in linux/etherdevice.h someday. */
39 struct device *init_etherdev(struct device *dev, int sizeof_private,
40 unsigned long *mem_startp);
41
42 /* The total size is unusually large: The 21040 aligns each of its 16
43 longword-wide registers on a quadword boundary. */
44 #define TULIP_TOTAL_SIZE 0x80
45
46 #ifdef HAVE_DEVLIST
47 struct netdev_entry tulip_drv =
48 {"Tulip", tulip_pci_probe, TULIP_TOTAL_SIZE, NULL};
49 #endif
50
51 #define TULIP_DEBUG 1
52 #ifdef TULIP_DEBUG
53 int tulip_debug = TULIP_DEBUG;
54 #else
55 int tulip_debug = 1;
56 #endif
57
58 /*
59 Theory of Operation
60
61 I. Board Compatibility
62
63 This device driver is designed for the DECchip 21040 "Tulip", Digital's
64 single-chip ethernet controller for PCI, as used on the SMC EtherPower
65 ethernet adapter.
66
67 II. Board-specific settings
68
69 PCI bus devices are configured by the system at boot time, so no jumpers
70 need to be set on the board. The system BIOS should be set to assign the
71 PCI INTA signal to an otherwise unused system IRQ line. While it's
72 physically possible to shared PCI interrupt lines, the kernel doesn't
73 support it.
74
75 III. Driver operation
76
77 IIIa. Ring buffers
78 The Tulip can use either ring buffers or lists of Tx and Rx descriptors.
79 The current driver uses a statically allocated Rx ring of descriptors and
80 buffers, and a list of the Tx buffers.
81
82 IIIC. Synchronization
83 The driver runs as two independent, single-threaded flows of control. One
84 is the send-packet routine, which enforces single-threaded use by the
85 dev->tbusy flag. The other thread is the interrupt handler, which is single
86 threaded by the hardware and other software.
87
88 The send packet thread has partial control over the Tx ring and 'dev->tbusy'
89 flag. It sets the tbusy flag whenever it's queuing a Tx packet. If the next
90 queue slot is empty, it clears the tbusy flag when finished otherwise it sets
91 the 'tp->tx_full' flag.
92
93 The interrupt handler has exclusive control over the Rx ring and records stats
94 from the Tx ring. (The Tx-done interrupt can't be selectively turned off, so
95 we can't avoid the interrupt overhead by having the Tx routine reap the Tx
96 stats.) After reaping the stats, it marks the queue entry as empty by setting
97 the 'base' to zero. Iff the 'tp->tx_full' flag is set, it clears both the
98 tx_full and tbusy flags.
99
100 IV. Notes
101
102 Thanks to Duke Kamstra of SMC for providing an EtherPower board.
103
104 The DEC databook doesn't document which Rx filter settings accept broadcast
105 packets. Nor does it document how to configure the part to configure the
106 serial subsystem for normal (vs. loopback) operation or how to have it
107 autoswitch between internal 10baseT, SIA and AUI transceivers.
108
109 The databook claims that CSR13, CSR14, and CSR15 should each be the last
110 register of the set CSR12-15 written. Hmmm, now how is that possible?
111 */
112
113 #define DEC_VENDOR_ID 0x1011 /* Hex 'D' :-> */
114 #define DEC_21040_ID 0x0002 /* Change for 21140. */
115
116 /* Keep the ring sizes a power of two for efficiency. */
117 #define TX_RING_SIZE 4
118 #define RX_RING_SIZE 4
119 #define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
120
121 /* Offsets to the Command and Status Registers, "CSRs". All accesses
122 must be longword instructions and quadword aligned. */
123 enum tulip_offsets {
124 CSR0=0, CSR1=0x08, CSR2=0x10, CSR3=0x18, CSR4=0x20, CSR5=0x28,
125 CSR6=0x30, CSR7=0x38, CSR8=0x40, CSR9=0x48, CSR10=0x50, CSR11=0x58,
126 CSR12=0x60, CSR13=0x68, CSR14=0x70, CSR15=0x78 };
127
128 /* The Tulip Rx and Tx buffer descriptors. */
129 struct tulip_rx_desc {
130 int status;
131 int length;
132 char *buffer1, *buffer2; /* We use only buffer 1. */
133 };
134
135 struct tulip_tx_desc {
136 int status;
137 int length;
138 char *buffer1, *buffer2; /* We use only buffer 1. */
139 };
140
141 struct tulip_private {
142 char devname[8]; /* Used only for kernel debugging. */
143 struct tulip_rx_desc rx_ring[RX_RING_SIZE];
144 struct tulip_tx_desc tx_ring[TX_RING_SIZE];
145 /* The saved address of a sent-in-place packet/buffer, for skfree(). */
146 struct sk_buff* tx_skbuff[TX_RING_SIZE];
147 long rx_buffs; /* Address of temporary Rx buffers. */
148 struct enet_statistics stats;
149 int setup_frame[48]; /* Pseudo-Tx frame to init address table. */
150 unsigned int cur_rx, cur_tx; /* The next free ring entry */
151 unsigned int dirty_rx, dirty_tx; /* The ring entries to be free()ed. */
152 unsigned int tx_full:1;
153 int pad0, pad1; /* Used for 8-byte alignment */
154 };
155
156 static unsigned long tulip_probe1(unsigned long mem_start, int ioaddr,
157 int irq);
158 static int tulip_open(struct device *dev);
159 static void tulip_init_ring(struct device *dev);
160 static int tulip_start_xmit(struct sk_buff *skb, struct device *dev);
161 static int tulip_rx(struct device *dev);
162 static void tulip_interrupt(int irq, struct pt_regs *regs);
163 static int tulip_close(struct device *dev);
164 static struct enet_statistics *tulip_get_stats(struct device *dev);
165 static void set_multicast_list(struct device *dev, int num_addrs, void *addrs);
166 static int set_mac_address(struct device *dev, void *addr);
167
168
169
170 /* This 21040 probe is unlike most other board probes. We can use memory
171 efficiently by allocating a large contiguous region and dividing it
172 ourselves. This is done by having the initialization occur before
173 the 'kmalloc()' memory management system is started. */
174
175 unsigned long dec21040_init(unsigned long mem_start, unsigned long mem_end)
/* ![[next]](../icons/right.png)
![[first]](../icons/n_first.png)
![[top]](../icons/top.png)
*/
176 {
177
178 if (pcibios_present()) {
179 int pci_index;
180 for (pci_index = 0; pci_index < 8; pci_index++) {
181 unsigned char pci_bus, pci_device_fn, pci_irq_line;
182 unsigned long pci_ioaddr;
183
184 if (pcibios_find_device (DEC_VENDOR_ID, DEC_21040_ID, pci_index,
185 &pci_bus, &pci_device_fn) != 0)
186 break;
187 pcibios_read_config_byte(pci_bus, pci_device_fn,
188 PCI_INTERRUPT_LINE, &pci_irq_line);
189 pcibios_read_config_dword(pci_bus, pci_device_fn,
190 PCI_BASE_ADDRESS_0, &pci_ioaddr);
191 /* Remove I/O space marker in bit 0. */
192 pci_ioaddr &= ~3;
193 if (tulip_debug > 2)
194 printk("Found DEC PCI Tulip at I/O %#lx, IRQ %d.\n",
195 pci_ioaddr, pci_irq_line);
196 mem_start = tulip_probe1(mem_start, pci_ioaddr, pci_irq_line);
197 }
198 }
199
200 return mem_start;
201 }
202
203 unsigned long tulip_probe1(unsigned long mem_start, int ioaddr, int irq)
/* ![[previous]](../icons/left.png)
*/
204 {
205 static int did_version = 0; /* Already printed version info. */
206 struct device *dev;
207 struct tulip_private *tp;
208 int i;
209
210 if (tulip_debug > 0 && did_version++ == 0)
211 printk(version);
212
213 dev = init_etherdev(0, sizeof(struct tulip_private)
214 + PKT_BUF_SZ*RX_RING_SIZE,
215 &mem_start);
216
217 printk("%s: DEC 21040 Tulip at %#3x,", dev->name, ioaddr);
218
219 /* Stop the chip's Tx and Rx processes. */
220 outl(inl(ioaddr + CSR6) & ~0x2002, ioaddr + CSR6);
221 /* Clear the missed-packet counter. */
222 inl(ioaddr + CSR8) & 0xffff;
223
224 /* The station address ROM is read byte serially. The register must
225 be polled, waiting for the value to be read bit serially from the
226 EEPROM.
227 */
228 outl(0, ioaddr + CSR9); /* Reset the pointer with a dummy write. */
229 for (i = 0; i < 6; i++) {
230 int value, boguscnt = 100000;
231 do
232 value = inl(ioaddr + CSR9);
233 while (value < 0 && --boguscnt > 0);
234 printk(" %2.2x", dev->dev_addr[i] = value);
235 }
236 printk(", IRQ %d\n", irq);
237
238 /* We do a request_region() only to register /proc/ioports info. */
239 request_region(ioaddr, TULIP_TOTAL_SIZE, "DEC Tulip Ethernet");
240
241 dev->base_addr = ioaddr;
242 dev->irq = irq;
243
244 /* Make certain the data structures are quadword aligned. */
245 dev->priv = (void *)(((int)dev->priv + 7) & ~7);
246 tp = (struct tulip_private *)dev->priv;
247 tp->rx_buffs = (long)dev->priv + sizeof(struct tulip_private);
248
249 /* The Tulip-specific entries in the device structure. */
250 dev->open = &tulip_open;
251 dev->hard_start_xmit = &tulip_start_xmit;
252 dev->stop = &tulip_close;
253 dev->get_stats = &tulip_get_stats;
254 #ifdef HAVE_MULTICAST
255 dev->set_multicast_list = &set_multicast_list;
256 #endif
257 #ifdef HAVE_SET_MAC_ADDR
258 dev->set_mac_address = &set_mac_address;
259 #endif
260
261 return mem_start;
262 }
263
264
265 static int
266 tulip_open(struct device *dev)
/* */
267 {
268 struct tulip_private *tp = (struct tulip_private *)dev->priv;
269 int ioaddr = dev->base_addr;
270
271 /* Reset the chip, holding bit 0 set at least 10 PCI cycles. */
272 outl(0xfff80001, ioaddr + CSR0);
273 SLOW_DOWN_IO;
274 /* Deassert reset. Set 8 longword cache alignment, 8 longword burst.
275 Cache alignment bits 15:14 Burst length 13:8
276 0000 No alignment 0x00000000 unlimited 0800 8 longwords
277 4000 8 longwords 0100 1 longword 1000 16 longwords
278 8000 16 longwords 0200 2 longwords 2000 32 longwords
279 C000 32 longwords 0400 4 longwords
280 Wait the specified 50 PCI cycles after a reset by initializing
281 Tx and Rx queues and the address filter list. */
282 outl(0xfff84800, ioaddr + CSR0);
283
284 if (irq2dev_map[dev->irq] != NULL
285 || (irq2dev_map[dev->irq] = dev) == NULL
286 || dev->irq == 0
287 || request_irq(dev->irq, &tulip_interrupt, 0, "DEC 21040 Tulip")) {
288 return -EAGAIN;
289 }
290
291 if (tulip_debug > 1)
292 printk("%s: tulip_open() irq %d.\n", dev->name, dev->irq);
293
294 tulip_init_ring(dev);
295
296 /* Fill the whole address filter table with our physical address. */
297 {
298 unsigned short *eaddrs = (unsigned short *)dev->dev_addr;
299 int *setup_frm = tp->setup_frame, i;
300
301 /* You must add the broadcast address when doing perfect filtering! */
302 *setup_frm++ = 0xffff;
303 *setup_frm++ = 0xffff;
304 *setup_frm++ = 0xffff;
305 /* Fill the rest of the accept table with our physical address. */
306 for (i = 1; i < 16; i++) {
307 *setup_frm++ = eaddrs[0];
308 *setup_frm++ = eaddrs[1];
309 *setup_frm++ = eaddrs[2];
310 }
311 /* Put the setup frame on the Tx list. */
312 tp->tx_ring[0].length = 0x08000000 | 192;
313 tp->tx_ring[0].buffer1 = (char *)tp->setup_frame;
314 tp->tx_ring[0].buffer2 = 0;
315 tp->tx_ring[0].status = 0x80000000;
316
317 tp->cur_tx++, tp->dirty_tx++;
318 }
319
320 outl((int)tp->rx_ring, ioaddr + CSR3);
321 outl((int)tp->tx_ring, ioaddr + CSR4);
322
323 /* Turn on the xcvr interface. */
324 outl(0x00000000, ioaddr + CSR13);
325 outl(0x00000004, ioaddr + CSR13);
326
327 /* Start the chip's Tx and Rx processes. */
328 outl(0xfffe2002, ioaddr + CSR6);
329
330 /* Trigger an immediate transmit demand to process the setup frame. */
331 outl(0, ioaddr + CSR1);
332
333 dev->tbusy = 0;
334 dev->interrupt = 0;
335 dev->start = 1;
336
337 /* Enable interrupts by setting the interrupt mask. */
338 outl(0xFFFFFFFF, ioaddr + CSR7);
339
340 if (tulip_debug > 2) {
341 printk("%s: Done tulip_open(), CSR0 %8.8x, CSR13 %8.8x.\n",
342 dev->name, inl(ioaddr + CSR0), inl(ioaddr + CSR13));
343 }
344 return 0;
345 }
346
347 /* Initialize the Rx and Tx rings, along with various 'dev' bits. */
348 static void
349 tulip_init_ring(struct device *dev)
/* */
350 {
351 struct tulip_private *tp = (struct tulip_private *)dev->priv;
352 int i;
353
354 tp->tx_full = 0;
355 tp->cur_rx = tp->cur_tx = 0;
356 tp->dirty_rx = tp->dirty_tx = 0;
357
358 for (i = 0; i < RX_RING_SIZE; i++) {
359 tp->rx_ring[i].status = 0x80000000; /* Owned by Tulip chip */
360 tp->rx_ring[i].length = PKT_BUF_SZ;
361 tp->rx_ring[i].buffer1 = (char *)(tp->rx_buffs + i*PKT_BUF_SZ);
362 tp->rx_ring[i].buffer2 = (char *)&tp->rx_ring[i+1];
363 }
364 /* Mark the last entry as wrapping the ring. */
365 tp->rx_ring[i-1].length = PKT_BUF_SZ | 0x02000000;
366 tp->rx_ring[i-1].buffer2 = (char *)&tp->rx_ring[0];
367
368 /* The Tx buffer descriptor is filled in as needed, but we
369 do need to clear the ownership bit. */
370 for (i = 0; i < TX_RING_SIZE; i++) {
371 tp->tx_ring[i].status = 0x00000000;
372 }
373 }
374
375 static int
376 tulip_start_xmit(struct sk_buff *skb, struct device *dev)
/* */
377 {
378 struct tulip_private *tp = (struct tulip_private *)dev->priv;
379 int ioaddr = dev->base_addr;
380 int entry;
381
382 /* Transmitter timeout, serious problems. */
383 if (dev->tbusy) {
384 int tickssofar = jiffies - dev->trans_start;
385 int i;
386 if (tickssofar < 20)
387 return 1;
388 printk("%s: transmit timed out, status %8.8x, SIA %8.8x %8.8x %8.8x %8.8x, resetting...\n",
389 dev->name, inl(ioaddr + CSR5), inl(ioaddr + CSR12),
390 inl(ioaddr + CSR13), inl(ioaddr + CSR14), inl(ioaddr + CSR15));
391 printk(" Rx ring %8.8x: ", (int)tp->rx_ring);
392 for (i = 0; i < RX_RING_SIZE; i++)
393 printk(" %8.8x", (unsigned int)tp->rx_ring[i].status);
394 printk("\n Tx ring %8.8x: ", (int)tp->tx_ring);
395 for (i = 0; i < TX_RING_SIZE; i++)
396 printk(" %8.8x", (unsigned int)tp->tx_ring[i].status);
397 printk("\n");
398
399 tp->stats.tx_errors++;
400 /* We should reinitialize the hardware here. */
401 dev->tbusy=0;
402 dev->trans_start = jiffies;
403 return 0;
404 }
405
406 if (skb == NULL || skb->len <= 0) {
407 printk("%s: Obsolete driver layer request made: skbuff==NULL.\n",
408 dev->name);
409 dev_tint(dev);
410 return 0;
411 }
412
413 /* Block a timer-based transmit from overlapping. This could better be
414 done with atomic_swap(1, dev->tbusy), but set_bit() works as well.
415 If this ever occurs the queue layer is doing something evil! */
416 if (set_bit(0, (void*)&dev->tbusy) != 0) {
417 printk("%s: Transmitter access conflict.\n", dev->name);
418 return 1;
419 }
420
421 /* Caution: the write order is important here, set the base address
422 with the "ownership" bits last. */
423
424 /* Calculate the next Tx descriptor entry. */
425 entry = tp->cur_tx % TX_RING_SIZE;
426
427 tp->tx_full = 1;
428 tp->tx_skbuff[entry] = skb;
429 tp->tx_ring[entry].length = skb->len |
430 (entry == TX_RING_SIZE-1 ? 0xe2000000 : 0xe0000000);
431 tp->tx_ring[entry].buffer1 = skb->data;
432 tp->tx_ring[entry].buffer2 = 0;
433 tp->tx_ring[entry].status = 0x80000000; /* Pass ownership to the chip. */
434
435 tp->cur_tx++;
436
437 /* Trigger an immediate transmit demand. */
438 outl(0, ioaddr + CSR1);
439
440 dev->trans_start = jiffies;
441
442 return 0;
443 }
444
445 /* The interrupt handler does all of the Rx thread work and cleans up
446 after the Tx thread. */
447 static void tulip_interrupt(int irq, struct pt_regs *regs)
/* */
448 {
449 struct device *dev = (struct device *)(irq2dev_map[irq]);
450 struct tulip_private *lp;
451 int csr5, ioaddr, boguscnt=10;
452
453 if (dev == NULL) {
454 printk ("tulip_interrupt(): irq %d for unknown device.\n", irq);
455 return;
456 }
457
458 ioaddr = dev->base_addr;
459 lp = (struct tulip_private *)dev->priv;
460 if (dev->interrupt)
461 printk("%s: Re-entering the interrupt handler.\n", dev->name);
462
463 dev->interrupt = 1;
464
465 do {
466 csr5 = inl(ioaddr + CSR5);
467 /* Acknowledge all of the current interrupt sources ASAP. */
468 outl(csr5 & 0x0001ffff, ioaddr + CSR5);
469
470 if (tulip_debug > 4)
471 printk("%s: interrupt csr5=%#8.8x new csr5=%#8.8x.\n",
472 dev->name, csr5, inl(dev->base_addr + CSR5));
473
474 if ((csr5 & 0x00018000) == 0)
475 break;
476
477 if (csr5 & 0x0040) /* Rx interrupt */
478 tulip_rx(dev);
479
480 if (csr5 & 0x0001) { /* Tx-done interrupt */
481 int dirty_tx = lp->dirty_tx;
482
483 while (dirty_tx < lp->cur_tx) {
484 int entry = dirty_tx % TX_RING_SIZE;
485 int status = lp->tx_ring[entry].status;
486
487 if (status < 0)
488 break; /* It still hasn't been Txed */
489
490 if (status & 0x8000) {
491 /* There was an major error, log it. */
492 lp->stats.tx_errors++;
493 if (status & 0x4104) lp->stats.tx_aborted_errors++;
494 if (status & 0x0C00) lp->stats.tx_carrier_errors++;
495 if (status & 0x0200) lp->stats.tx_window_errors++;
496 if (status & 0x0002) lp->stats.tx_fifo_errors++;
497 if (status & 0x0080) lp->stats.tx_heartbeat_errors++;
498 #ifdef ETHER_STATS
499 if (status & 0x0100) lp->stats.collisions16++;
500 #endif
501 } else {
502 #ifdef ETHER_STATS
503 if (status & 0x0001) lp->stats.tx_deferred++;
504 #endif
505 lp->stats.collisions += (status >> 3) & 15;
506 lp->stats.tx_packets++;
507 }
508
509 /* Free the original skb. */
510 dev_kfree_skb(lp->tx_skbuff[entry], FREE_WRITE);
511 dirty_tx++;
512 }
513
514 #ifndef final_version
515 if (lp->cur_tx - dirty_tx >= TX_RING_SIZE) {
516 printk("out-of-sync dirty pointer, %d vs. %d, full=%d.\n",
517 dirty_tx, lp->cur_tx, lp->tx_full);
518 dirty_tx += TX_RING_SIZE;
519 }
520 #endif
521
522 if (lp->tx_full && dev->tbusy
523 && dirty_tx > lp->cur_tx - TX_RING_SIZE + 2) {
524 /* The ring is no longer full, clear tbusy. */
525 lp->tx_full = 0;
526 dev->tbusy = 0;
527 mark_bh(NET_BH);
528 }
529
530 lp->dirty_tx = dirty_tx;
531 }
532
533 /* Log errors. */
534 if (csr5 & 0x8000) { /* Abnormal error summary bit. */
535 if (csr5 & 0x0008) lp->stats.tx_errors++; /* Tx babble. */
536 if (csr5 & 0x0100) { /* Missed a Rx frame. */
537 lp->stats.rx_errors++;
538 lp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
539 }
540 if (csr5 & 0x0800) {
541 printk("%s: Something Wicked happened! %8.8x.\n",
542 dev->name, csr5);
543 /* Hmmmmm, it's not clear what to do here. */
544 }
545 }
546 if (--boguscnt < 0) {
547 printk("%s: Too much work at interrupt, csr5=0x%8.8x.\n",
548 dev->name, csr5);
549 /* Clear all interrupt sources. */
550 outl(0x0001ffff, ioaddr + CSR5);
551 break;
552 }
553 } while (1);
554
555 if (tulip_debug > 3)
556 printk("%s: exiting interrupt, csr5=%#4.4x.\n",
557 dev->name, inl(ioaddr + CSR5));
558
559 /* Special code for testing *only*. */
560 {
561 static int stopit = 10;
562 if (dev->start == 0 && --stopit < 0) {
563 printk("%s: Emergency stop, looping startup interrupt.\n",
564 dev->name);
565 free_irq(irq);
566 }
567 }
568
569 dev->interrupt = 0;
570 return;
571 }
572
573 static int
574 tulip_rx(struct device *dev)
/* */
575 {
576 struct tulip_private *lp = (struct tulip_private *)dev->priv;
577 int entry = lp->cur_rx % RX_RING_SIZE;
578 int i;
579
580 if (tulip_debug > 4)
581 printk(" In tulip_rx().\n");
582 /* If we own the next entry, it's a new packet. Send it up. */
583 while (lp->rx_ring[entry].status >= 0) {
584 int status = lp->rx_ring[entry].status;
585
586 if (tulip_debug > 4)
587 printk(" tulip_rx() status was %8.8x.\n", status);
588 if ((status & 0x0300) != 0x0300) {
589 printk("%s: Ethernet frame spanned multiple buffers, status %8.8x!\n",
590 dev->name, status);
591 } else if (status & 0x8000) {
592 /* There was a fatal error. */
593 lp->stats.rx_errors++; /* end of a packet.*/
594 if (status & 0x0890) lp->stats.rx_length_errors++;
595 if (status & 0x0004) lp->stats.rx_frame_errors++;
596 if (status & 0x0002) lp->stats.rx_crc_errors++;
597 if (status & 0x0001) lp->stats.rx_fifo_errors++;
598 } else {
599 /* Malloc up new buffer, compatible with net-2e. */
600 short pkt_len = lp->rx_ring[entry].status >> 16;
601 struct sk_buff *skb;
602
603 skb = alloc_skb(pkt_len, GFP_ATOMIC);
604 if (skb == NULL) {
605 printk("%s: Memory squeeze, deferring packet.\n", dev->name);
606 /* Check that at least two ring entries are free.
607 If not, free one and mark stats->rx_dropped++. */
608 for (i=0; i < RX_RING_SIZE; i++)
609 if (lp->rx_ring[(entry+i) % RX_RING_SIZE].status < 0)
610 break;
611
612 if (i > RX_RING_SIZE -2) {
613 lp->stats.rx_dropped++;
614 lp->rx_ring[entry].status = 0x80000000;
615 lp->cur_rx++;
616 }
617 break;
618 }
619 skb->len = pkt_len;
620 skb->dev = dev;
621 memcpy(skb->data, lp->rx_ring[entry].buffer1, pkt_len);
622 netif_rx(skb);
623 lp->stats.rx_packets++;
624 }
625
626 lp->rx_ring[entry].status = 0x80000000;
627 entry = (++lp->cur_rx) % RX_RING_SIZE;
628 }
629
630 return 0;
631 }
632
633 static int
634 tulip_close(struct device *dev)
/* */
635 {
636 int ioaddr = dev->base_addr;
637 struct tulip_private *tp = (struct tulip_private *)dev->priv;
638
639 dev->start = 0;
640 dev->tbusy = 1;
641
642 if (tulip_debug > 1)
643 printk("%s: Shutting down ethercard, status was %2.2x.\n",
644 dev->name, inl(ioaddr + CSR5));
645
646 /* Disable interrupts by clearing the interrupt mask. */
647 outl(0x00000000, ioaddr + CSR7);
648 /* Stop the chip's Tx and Rx processes. */
649 outl(inl(ioaddr + CSR6) & ~0x2002, ioaddr + CSR6);
650
651 tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
652
653 free_irq(dev->irq);
654 irq2dev_map[dev->irq] = 0;
655
656 return 0;
657 }
658
659 static struct enet_statistics *
660 tulip_get_stats(struct device *dev)
/* */
661 {
662 struct tulip_private *tp = (struct tulip_private *)dev->priv;
663 short ioaddr = dev->base_addr;
664
665 tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
666
667 return &tp->stats;
668 }
669
670 /* Set or clear the multicast filter for this adaptor.
671 num_addrs == -1 Promiscuous mode, receive all packets
672 num_addrs == 0 Normal mode, clear multicast list
673 num_addrs > 0 Multicast mode, receive normal and MC packets, and do
674 best-effort filtering.
675 */
676 static void
677 set_multicast_list(struct device *dev, int num_addrs, void *addrs)
/* */
678 {
679 short ioaddr = dev->base_addr;
680 int csr6 = inl(ioaddr + CSR6) & ~0x00D5;
681
682 if (num_addrs > 15) {
683 /* Too many to filter perfectly -- accept all multicasts. */
684 outl(csr6 | 0x0080, ioaddr + CSR6);
685 } else if (num_addrs < 0) { /* Set promiscuous. */
686 outl(csr6 | 0x00C0, ioaddr + CSR6);
687 /* Log any net taps. */
688 printk("%s: Promiscuous mode enabled.\n", dev->name);
689 } else {
690 struct tulip_private *tp = (struct tulip_private *)dev->priv;
691 int *setup_frm = tp->setup_frame;
692 unsigned short *eaddrs = addrs;
693 int i;
694
695 /* We have <= 15 addresses that we can use the wonderful
696 16 address perfect filtering of the Tulip. Note that only
697 the low shortword of setup_frame[] is valid. */
698 outl(csr6 | 0x0000, ioaddr + CSR6);
699 for(i = 0; i < num_addrs; i++) {
700 *setup_frm++ = *eaddrs++;
701 *setup_frm++ = *eaddrs++;
702 *setup_frm++ = *eaddrs++;
703 }
704 /* Fill the rest of the table with our physical address. */
705 eaddrs = (unsigned short *)dev->dev_addr;
706 do {
707 *setup_frm++ = eaddrs[0];
708 *setup_frm++ = eaddrs[1];
709 *setup_frm++ = eaddrs[2];
710 } while (++i < 16);
711
712 /* Now add this frame to the Tx list. */
713 }
714 }
715
716 static int
717 set_mac_address(struct device *dev, void *addr)
/* ![[last]](../icons/n_last.png)
*/
718 {
719 int i;
720 if (dev->start)
721 return -EBUSY;
722 printk("%s: Setting MAC address to ", dev->name);
723 for (i = 0; i < 6; i++)
724 printk(" %2.2x", dev->dev_addr[i] = ((unsigned char *)addr)[i]);
725 printk(".\n");
726 return 0;
727 }
728
729
730 /*
731 * Local variables:
732 * compile-command: "gcc -D__KERNEL__ -I/usr/src/linux/net/inet -Wall -Wstrict-prototypes -O6 -m486 -c tulip.c"
733 * c-indent-level: 4
734 * tab-width: 4
735 * End:
736 */
![[bottom]](../icons/n_bottom.png){kind=icon}
*/