![[bottom]](../icons/bottom.png){kind=icon}
![[previous]](../icons/n_left.png){kind=icon}
![[next]](../icons/n_right.png){kind=icon}
![[first]](../icons/n_first.png){kind=icon}
![[last]](../icons/n_last.png){kind=icon}
![[top]](../icons/n_top.png){kind=icon}
![[index]](../icons/index.png){kind=icon}
![[help]](../icons/help.png){kind=icon}
*/
1 /*
2 * hp100.h: Hewlett Packard HP10/100VG ANY LAN ethernet driver for Linux.
3 *
4 * Author: Jaroslav Kysela, <perex@pf.jcu.cz>
5 *
6 * Header file...
7 *
8 * This driver is based on the 'hpfepkt' crynwr packet driver.
9 *
10 * This source/code is public free; you can distribute it and/or modify
11 * it under terms of the GNU General Public License (published by the
12 * Free Software Foundation) either version two of this License, or any
13 * later version.
14 */
15
16 /****************************************************************************
17 * Hardware Constants
18 ****************************************************************************/
19
20 /*
21 * ATT2MD01 Register Page Constants
22 */
23
24 #define HP100_PAGE_PERFORMANCE 0x0 /* Page 0 */
25 #define HP100_PAGE_MAC_ADDRESS 0x1 /* Page 1 */
26 #define HP100_PAGE_HW_MAP 0x2 /* Page 2 */
27 #define HP100_PAGE_EEPROM_CTRL 0x3 /* Page 3 */
28 #define HP100_PAGE_MAC_CTRL 0x4 /* Page 4 */
29 #define HP100_PAGE_MMU_CFG 0x5 /* Page 5 */
30 #define HP100_PAGE_ID_MAC_ADDR 0x6 /* Page 6 */
31 #define HP100_PAGE_MMU_POINTER 0x7 /* Page 7 */
32
33 /*
34 * ATT2MD01 Register Addresses
35 */
36
37 /* Present on all pages */
38
39 #define HP100_REG_HW_ID 0x00 /* R: (16) Unique card ID */
40 #define HP100_REG_TRACE 0x00 /* W: (16) Used for debug output */
41 #define HP100_REG_PAGING 0x02 /* R: (16),15:4 Card ID */
42 /* W: (16),3:0 Switch pages */
43 #define HP100_REG_OPTION_LSW 0x04 /* RW: (16) Select card functions */
44 #define HP100_REG_OPTION_MSW 0x06 /* RW: (16) Select card functions */
45
46 /* Page 0 - Performance */
47
48 #define HP100_REG_IRQ_STATUS 0x08 /* RW: (16) Which ints are pending */
49 #define HP100_REG_IRQ_MASK 0x0a /* RW: (16) Select ints to allow */
50 #define HP100_REG_FRAGMENT_LEN 0x0c /* RW: (16)12:0 Current fragment len */
51 #define HP100_REG_OFFSET 0x0e /* RW: (16)12:0 Offset to start read */
52 #define HP100_REG_DATA32 0x10 /* RW: (32) I/O mode data port */
53 #define HP100_REG_DATA16 0x12 /* RW: WORDs must be read from here */
54 #define HP100_REG_TX_MEM_FREE 0x14 /* RD: (32) Amount of free Tx mem */
55 #define HP100_REG_RX_PKT_CNT 0x18 /* RD: (8) Rx count of pkts on card */
56 #define HP100_REG_TX_PKT_CNT 0x19 /* RD: (8) Tx count of pkts on card */
57
58 /* Page 1 - MAC Address/Hash Table */
59
60 #define HP100_REG_MAC_ADDR 0x08 /* RW: (8) Cards MAC address */
61 #define HP100_REG_HASH_BYTE0 0x10 /* RW: (8) Cards multicast filter */
62
63 /* Page 2 - Hardware Mapping */
64
65 #define HP100_REG_MEM_MAP_LSW 0x08 /* RW: (16) LSW of cards mem addr */
66 #define HP100_REG_MEM_MAP_MSW 0x0a /* RW: (16) MSW of cards mem addr */
67 #define HP100_REG_IO_MAP 0x0c /* RW: (8) Cards I/O address */
68 #define HP100_REG_IRQ_CHANNEL 0x0d /* RW: (8) IRQ and edge/level int */
69 #define HP100_REG_SRAM 0x0e /* RW: (8) How much RAM on card */
70 #define HP100_REG_BM 0x0f /* RW: (8) Controls BM functions */
71
72 /* Page 3 - EEPROM/Boot ROM */
73
74 #define HP100_REG_EEPROM_CTRL 0x08 /* RW: (16) Used to load EEPROM */
75
76 /* Page 4 - LAN Configuration */
77
78 #define HP100_REG_LAN_CFG_10 0x08 /* RW: (16) Set 10M XCVR functions */
79 #define HP100_REG_LAN_CFG_VG 0x0a /* RW: (16) Set 100M XCVR functions */
80 #define HP100_REG_MAC_CFG_1 0x0c /* RW: (8) Types of pkts to accept */
81 #define HP100_REG_MAC_CFG_2 0x0d /* RW: (8) Misc MAC functions */
82 /* The follow clear when read: */
83 #define HP100_REG_DROPPED 0x10 /* R: (16),11:0 Pkts cant fit in mem*/
84 #define HP100_REG_CRC 0x12 /* R: (8) Pkts with CRC */
85 #define HP100_REG_ABORT 0x13 /* R: (8) Aborted Tx pkts */
86
87 /* Page 5 - MMU */
88
89 #define HP100_REG_RX_MEM_STOP 0x0c /* RW: (16) End of Rx ring addr */
90 #define HP100_REG_TX_MEM_STOP 0x0e /* RW: (16) End of Tx ring addr */
91
92 /* Page 6 - Card ID/Physical LAN Address */
93
94 #define HP100_REG_BOARD_ID 0x08 /* R: (8) EISA/ISA card ID */
95 #define HP100_REG_BOARD_IO_CHCK 0x0c /* R: (8) Added to ID to get FFh */
96 #define HP100_REG_SOFT_MODEL 0x0d /* R: (8) Config program defined */
97 #define HP100_REG_LAN_ADDR 0x10 /* R: (8) MAC addr of card */
98 #define HP100_REG_LAN_ADDR_CHCK 0x16 /* R: (8) Added to addr to get FFh */
99
100 /* Page 7 - MMU Current Pointers */
101
102 #define HP100_REG_RX_MEM_BR 0x08 /* R: (16) Current begin of Rx ring */
103 #define HP100_REG_RX_MEM_ER 0x0a /* R: (16) Current end of Rx ring */
104 #define HP100_REG_TX_MEM_BR 0x0c /* R: (16) Current begin of Tx ring */
105 #define HP100_REG_TX_MEM_ER 0x0e /* R: (16) Current end of Rx ring */
106 #define HP100_REG_MEM_DEBUG 0x1a /* RW: (16) Used for memory tests */
107
108 /*
109 * HardwareIDReg bits/masks
110 */
111
112 #define HP100_HW_ID_0 0x50 /* Hardware ID bytes. */
113 #define HP100_HW_ID_1 0x48
114 #define HP100_HW_ID_2_REVA 0x50 /* Rev. A ID. NOTE: lower nibble not used */
115 #define HP100_HW_ID_3 0x53
116
117 /*
118 * OptionLSWReg bits/masks
119 */
120
121 #define HP100_DEBUG_EN 0x8000 /* 0:Disable, 1:Enable Debug Dump Pointer */
122 #define HP100_RX_HDR 0x4000 /* 0:Disable, 1:Enable putting pkt into */
123 /* system memory before Rx interrupt */
124 #define HP100_MMAP_DIS 0x2000 /* 0:Enable, 1:Disable memory mapping. */
125 /* MMAP_DIS must be 0 and MEM_EN must */
126 /* be 1 for memory-mapped mode to be */
127 /* enabled */
128 #define HP100_EE_EN 0x1000 /* 0:Disable,1:Enable EEPROM writing */
129 #define HP100_BM_WRITE 0x0800 /* 0:Slave, 1:Bus Master for Tx data */
130 #define HP100_BM_READ 0x0400 /* 0:Slave, 1:Bus Master for Rx data */
131 #define HP100_TRI_INT 0x0200 /* 0:Dont, 1:Do tri-state the int */
132 #define HP100_MEM_EN 0x0040 /* Config program set this to */
133 /* 0:Disable, 1:Enable mem map. */
134 /* See MMAP_DIS. */
135 #define HP100_IO_EN 0x0020 /* 0:Disable, 1:Enable I/O transfers */
136 #define HP100_BOOT_EN 0x0010 /* 0:Disable, 1:Enable boot ROM access */
137 #define HP100_FAKE_INT 0x0008 /* 0:No int, 1:int */
138 #define HP100_INT_EN 0x0004 /* 0:Disable, 1:Enable ints from card */
139 #define HP100_HW_RST 0x0002 /* 0:Reset, 1:Out of reset */
140
141 /*
142 * OptionMSWReg bits/masks
143 */
144 #define HP100_PRIORITY_TX 0x0080 /* 0:Don't, 1:Do all Tx pkts as priority */
145 #define HP100_EE_LOAD 0x0040 /* 1:EEPROM loading, 0 when done */
146 #define HP100_ADV_NXT_PKT 0x0004 /* 1:Advance to next pkt in Rx queue, */
147 /* h/w will set to 0 when done */
148 #define HP100_TX_CMD 0x0002 /* 1:Tell h/w download done, h/w will set */
149 /* to 0 when done */
150
151 /*
152 * InterruptStatusReg/InterruptMaskReg bits/masks. These bits will 0 when a 1
153 * is written to them.
154 */
155 #define HP100_RX_PACKET 0x0400 /* 0:No, 1:Yes pkt has been Rx */
156 #define HP100_RX_ERROR 0x0200 /* 0:No, 1:Yes Rx pkt had error */
157 #define HP100_TX_SPACE_AVAIL 0x0010 /* 0:<8192, 1:>=8192 Tx free bytes */
158 #define HP100_TX_COMPLETE 0x0008 /* 0:No, 1:Yes a Tx has completed */
159 #define HP100_TX_ERROR 0x0002 /* 0:No, 1:Yes Tx pkt had error */
160
161 /*
162 * TxMemoryFreeCountReg bits/masks.
163 */
164 #define HP100_AUTO_COMPARE 0x8000 /* Says at least 8k is available for Tx. */
165 /* NOTE: This mask is for the upper */
166 /* word of the register. */
167
168 /*
169 * IRQChannelReg bits/masks.
170 */
171 #define HP100_ZERO_WAIT_EN 0x80 /* 0:No, 1:Yes assers NOWS signal */
172 #define HP100_LEVEL_IRQ 0x10 /* 0:Edge, 1:Level type interrupts. */
173 /* Only valid on EISA cards. */
174 #define HP100_IRQ_MASK 0x0F /* Isolate the IRQ bits */
175
176 /*
177 * SRAMReg bits/masks.
178 */
179 #define HP100_RAM_SIZE_MASK 0xe0 /* AND to get SRAM size index */
180 #define HP100_RAM_SIZE_SHIFT 0x05 /* Shift count to put index in lower bits */
181
182 /*
183 * BMReg bits/masks.
184 */
185 #define HP100_BM_SLAVE 0x04 /* 0:Slave, 1:BM mode */
186
187 /*
188 * EEPROMControlReg bits/masks.
189 */
190 #define HP100_EEPROM_LOAD 0x0001 /* 0->1 loads the EEPROM into registers. */
191 /* When it goes back to 0, load is */
192 /* complete. This should take ~600us. */
193
194 /*
195 * LANCntrCfg10Reg bits/masks.
196 */
197 #define HP100_SQU_ST 0x0100 /* 0:No, 1:Yes collision signal sent */
198 /* after Tx. Only used for AUI. */
199 #define HP100_MAC10_SEL 0x00c0 /* Get bits to indicate MAC */
200 #define HP100_AUI_SEL 0x0020 /* Status of AUI selection */
201 #define HP100_LOW_TH 0x0010 /* 0:No, 1:Yes allow better cabling */
202 #define HP100_LINK_BEAT_DIS 0x0008 /* 0:Enable, 1:Disable link beat */
203 #define HP100_LINK_BEAT_ST 0x0004 /* 0:No, 1:Yes link beat being Rx */
204 #define HP100_R_ROL_ST 0x0002 /* 0:No, 1:Yes Rx twisted pair has been */
205 /* reversed */
206 #define HP100_AUI_ST 0x0001 /* 0:No, 1:Yes use AUI on TP card */
207
208 /* MAC Selection, use with MAC10_SEL bits */
209 #define HP100_AUTO_SEL_10 0x0 /* Auto select */
210 #define HP100_XCVR_LXT901_10 0x1 /* LXT901 10BaseT transceiver */
211 #define HP100_XCVR_7213 0x2 /* 7213 transceiver */
212 #define HP100_XCVR_82503 0x3 /* 82503 transceiver */
213
214
215 /*
216 * LANCntrCfgVGReg bits/masks.
217 */
218 #define HP100_FRAME_FORMAT 0x0800 /* 0:802.3, 1:802.5 frames */
219 #define HP100_BRIDGE 0x0400 /* 0:No, 1:Yes tell hub it's a bridge */
220 #define HP100_PROM_MODE 0x0200 /* 0:No, 1:Yes tell hub card is */
221 /* promiscuous */
222 #define HP100_REPEATER 0x0100 /* 0:No, 1:Yes tell hub MAC wants to be */
223 /* a cascaded repeater */
224 #define HP100_MAC100_SEL 0x0080 /* 0:No, 1:Yes use 100 Mbit MAC */
225 #define HP100_LINK_UP_ST 0x0040 /* 0:No, 1:Yes endnode logged in */
226 #define HP100_LINK_CABLE_ST 0x0020 /* 0:No, 1:Yes cable can hear tones from */
227 /* hub */
228 #define HP100_LOAD_ADDR 0x0010 /* 0->1 card addr will be sent to hub. */
229 /* 100ms later the link status bits are */
230 /* valid */
231 #define HP100_LINK_CMD 0x0008 /* 0->1 link will attempt to log in. */
232 /* 100ms later the link status bits are */
233 /* valid */
234 #define HP100_LINK_GOOD_ST 0x0002 /* 0:No, 1:Yes cable passed training */
235 #define HP100_VG_RESET 0x0001 /* 0:Yes, 1:No reset the 100VG MAC */
236
237
238 /*
239 * MACConfiguration1Reg bits/masks.
240 */
241 #define HP100_RX_IDLE 0x80 /* 0:Yes, 1:No currently receiving pkts */
242 #define HP100_TX_IDLE 0x40 /* 0:Yes, 1:No currently Txing pkts */
243 #define HP100_RX_EN 0x20 /* 0:No, 1:Yes allow receiving of pkts */
244 #define HP100_TX_EN 0x10 /* 0:No, 1:Yes allow transmiting of pkts */
245 #define HP100_ACC_ERRORED 0x08 /* 0:No, 1:Yes allow Rx of errored pkts */
246 #define HP100_ACC_MC 0x04 /* 0:No, 1:Yes allow Rx of multicast pkts */
247 #define HP100_ACC_BC 0x02 /* 0:No, 1:Yes allow Rx of broadcast pkts */
248 #define HP100_ACC_PHY 0x01 /* 0:No, 1:Yes allow Rx of ALL physical pkts */
249
250 #define HP100_MAC1MODEMASK 0xf0 /* Hide ACC bits */
251 #define HP100_MAC1MODE1 0x00 /* Receive nothing, must also disable RX */
252 #define HP100_MAC1MODE2 0x00
253 #define HP100_MAC1MODE3 HP100_MAC1MODE2 | HP100_ACC_BC
254 #define HP100_MAC1MODE4 HP100_MAC1MODE3 | HP100_ACC_MC
255 #define HP100_MAC1MODE5 HP100_MAC1MODE4 /* set mc hash to all ones also */
256 #define HP100_MAC1MODE6 HP100_MAC1MODE5 | HP100_ACC_PHY /* Promiscuous */
257
258 /* Note MODE6 will receive all GOOD packets on the LAN. This really needs
259 a mode 7 defined to be LAN Analyzer mode, which will receive errored and
260 runt packets, and keep the CRC bytes. */
261
262 #define HP100_MAC1MODE7 MAC1MODE6 OR ACC_ERRORED
263
264 /*
265 * MACConfiguration2Reg bits/masks.
266 */
267 #define HP100_TR_MODE 0x80 /* 0:No, 1:Yes support Token Ring formats */
268 #define HP100_TX_SAME 0x40 /* 0:No, 1:Yes Tx same packet continuous */
269 #define HP100_LBK_XCVR 0x20 /* 0:No, 1:Yes loopback through MAC & */
270 /* transceiver */
271 #define HP100_LBK_MAC 0x10 /* 0:No, 1:Yes loopback through MAC */
272 #define HP100_CRC_I 0x08 /* 0:No, 1:Yes inhibit CRC on Tx packets */
273 #define HP100_KEEP_CRC 0x02 /* 0:No, 1:Yes keep CRC on Rx packets. */
274 /* The length will reflect this. */
275
276 #define HP100_MAC2MODEMASK 0x02
277 #define HP100_MAC2MODE1 0x00
278 #define HP100_MAC2MODE2 0x00
279 #define HP100_MAC2MODE3 0x00
280 #define HP100_MAC2MODE4 0x00
281 #define HP100_MAC2MODE5 0x00
282 #define HP100_MAC2MODE6 0x00
283 #define HP100_MAC2MODE7 KEEP_CRC
284
285 /*
286 * Set/Reset bits
287 */
288 #define HP100_SET_HB 0x0100 /* 0:Set fields to 0 whose mask is 1 */
289 #define HP100_SET_LB 0x0001 /* HB sets upper byte, LB sets lower byte */
290 #define HP100_RESET_HB 0x0000 /* For readability when resetting bits */
291 #define HP100_RESET_LB 0x0000 /* For readability when resetting bits */
292
293 /*
294 * Misc. Constants
295 */
296 #define HP100_LAN_100 100 /* lan_type value for VG */
297 #define HP100_LAN_10 10 /* lan_type value for 10BaseT */
298 #define HP100_LAN_ERR (-1) /* lan_type value for link down */
299
300 /*
301 * Receive Header Definition.
302 */
303
304 struct hp100_rx_header {
305 u_short rx_length; /* Pkt length is bits 12:0 */
306 u_short rx_status; /* status of the packet */
307 };
308
309 #define HP100_PKT_LEN_MASK 0x1FFF /* AND with RxLength to get length bits */
310
311 /* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED
312 bit in the MAC Configuration Register 1 is set. */
313
314 #define HP100_RX_PRI 0x8000 /* 0:No, 1:Yes packet is priority */
315 #define HP100_SDF_ERR 0x4000 /* 0:No, 1:Yes start of frame error */
316 #define HP100_SKEW_ERR 0x2000 /* 0:No, 1:Yes skew out of range */
317 #define HP100_BAD_SYMBOL_ERR 0x1000 /* 0:No, 1:Yes invalid symbol received */
318 #define HP100_RCV_IPM_ERR 0x0800 /* 0:No, 1:Yes pkt had an invalid packet */
319 /* marker */
320 #define HP100_SYMBOL_BAL_ERR 0x0400 /* 0:No, 1:Yes symbol balance error */
321 #define HP100_VG_ALN_ERR 0x0200 /* 0:No, 1:Yes non-octet received */
322 #define HP100_TRUNC_ERR 0x0100 /* 0:No, 1:Yes the packet was truncated */
323 #define HP100_RUNT_ERR 0x0040 /* 0:No, 1:Yes pkt length < Min Pkt */
324 /* Length Reg. */
325 #define HP100_ALN_ERR 0x0010 /* 0:No, 1:Yes align error. */
326 #define HP100_CRC_ERR 0x0008 /* 0:No, 1:Yes CRC occurred. */
327
328 /* The last three bits indicate the type of destination address */
329
330 #define HP100_MULTI_ADDR_HASH 0x0006 /* 110: Addr multicast, matched hash */
331 #define HP100_BROADCAST_ADDR 0x0003 /* x11: Addr broadcast */
332 #define HP100_MULTI_ADDR_NO_HASH 0x0002 /* 010: Addr multicast, didn't match hash */
333 #define HP100_PHYS_ADDR_MATCH 0x0001 /* x01: Addr was physical and mine */
334 #define HP100_PHYS_ADDR_NO_MATCH 0x0000 /* x00: Addr was physical but not mine */
335
336 /*
337 * macros
338 */
339
340 #define hp100_inb( reg ) \
341 inb( ioaddr + HP100_REG_##reg )
342 #define hp100_inw( reg ) \
343 inw( ioaddr + HP100_REG_##reg )
344 #define hp100_inl( reg ) \
345 inl( ioaddr + HP100_REG_##reg )
346 #define hp100_outb( data, reg ) \
347 outb( data, ioaddr + HP100_REG_##reg )
348 #define hp100_outw( data, reg ) \
349 outw( data, ioaddr + HP100_REG_##reg )
350 #define hp100_outl( data, reg ) \
351 outl( data, ioaddr + HP100_REG_##reg )
352 #define hp100_orb( data, reg ) \
353 outb( inb( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg )
354 #define hp100_orw( data, reg ) \
355 outw( inw( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg )
356 #define hp100_andb( data, reg ) \
357 outb( inb( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg )
358 #define hp100_andw( data, reg ) \
359 outw( inw( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg )
360
361 #define hp100_page( page ) \
362 outw( HP100_PAGE_##page, ioaddr + HP100_REG_PAGING )
363 #define hp100_ints_off() \
364 outw( HP100_INT_EN | HP100_RESET_LB, ioaddr + HP100_REG_OPTION_LSW )
365 #define hp100_ints_on() \
366 outw( HP100_INT_EN | HP100_SET_LB, ioaddr + HP100_REG_OPTION_LSW )
367 #define hp100_mem_map_enable() \
368 outw( HP100_MMAP_DIS | HP100_RESET_HB, ioaddr + HP100_REG_OPTION_LSW )
369 #define hp100_mem_map_disable() \
370 outw( HP100_MMAP_DIS | HP100_SET_HB, ioaddr + HP100_REG_OPTION_LSW )
371 #define hp100_reset_card() \
372 outw( HP100_HW_RST | HP100_RESET_LB, ioaddr + HP100_REG_OPTION_LSW )
373 #define hp100_unreset_card() \
374 outw( HP100_HW_RST | HP100_SET_LB, ioaddr + HP100_REG_OPTION_LSW )
![[top]](../icons/top.png){kind=icon}
![[bottom]](../icons/n_bottom.png){kind=icon}
*/